- 您現在的位置：買賣IC網 > PDF目錄203637 > W9412G2IB-4 (WINBOND ELECTRONICS CORP) 4M X 32 DDR DRAM, 0.6 ns, PBGA144 PDF資料下載
參數資料
| 型號： | W9412G2IB-4 |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | DRAM |
| 英文描述： | 4M X 32 DDR DRAM, 0.6 ns, PBGA144 |
| 封裝： | 12 X 12 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, LFBGA-144 |
| 文件頁數： | 5/50頁 |
| 文件大小： | 826K |
| 代理商： | W9412G2IB-4 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
W9412G2IB
Publication Release Date: Aug. 30, 2010
- 13 -
Revision A06
The refresh addressing is generated by the internal refresh controller. This makes the address
bits ”Don’t Care” during an AUTO REFRESH command. The DDR SDRAM requires AUTO RE-
FRESH cycles at an average periodic interval of tREFI (maximum).
To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the
absolute refresh interval is provided. A maximum of eight AUTO REFRESH commands can be
posted to any given DDR SDRAM, and the maximum absolute interval between any AUTO
REFRESH command and the next AUTO REFRESH command is 8 * tREFI.
7.2.14
Self Refresh Entry Command
( RAS = “L”, CAS = “L”, WE = “H”, CKE = “L”, BA0, BA1, A0 to A11 = Don’t Care)
The SELF REFRESH command can be used to retain data in the DDR SDRAM, even if the rest of
the system is powered down. When in the self refresh mode, the DDR SDRAM retains data
without external clocking. The SELF REFRESH command is initiated like an AUTO REFRESH
command except CKE is disabled (LOW). The DLL is automatically disabled upon entering SELF
REFRESH, and is automatically enabled upon exiting SELF REFRESH. Any time the DLL is
enabled a DLL Reset must follow and 200 clock cycles should occur before a READ command
can be issued. Input signals except CKE are “Don’t Care” during SELF REFRESH. Since CKE is
an SSTL_2 input, VREF must be maintained during SELF REFRESH.
7.2.15
Self Refresh Exit Command
(CKE = “H”, CS = “H” or CKE = “H”, RAS = “H”, CAS = “H”)
The procedure for exiting self refresh requires a sequence of commands. First, CLK must be
stable prior to CKE going back HIGH. Once CKE is HIGH, the DDR SDRAM must have NOP
commands issued for tXSNR because time is required for the completion of any internal refresh in
progress. A simple algorithm for meeting both refresh and DLL requirements is to apply NOPs for
200 clock cycles before applying any other command.
The use of SELF REFREH mode introduces the possibility that an internally timed event can be
missed when CKE is raised for exit from self refresh mode. Upon exit from SELF REFRESH an
extra auto refresh command is recommended.
7.2.16
Data Write Enable /Disable Command
(DM = “L/H” or DM0
DM3 = “L/H”)
During a Write cycle, the DM0
DM3, DMs signal functions as Data Mask and can control every
word of the input data. The DM0 signal controls DQ0 to DQ7, DM1 signal controls DQ8 to DQ15,
DM2 signal controls DQ16 to DQ23 and DM3 signal controls DQ24 to DQ31.
7.3 Read Operation
Issuing the Bank Activate command to the idle bank puts it into the active state. When the Read
command is issued after tRCD from the Bank Activate command, the data is read out sequentially,
synchronized with both edges of DQS (Burst Read operation). The initial read data becomes
available after CAS Latency from the issuing of the Read command. The CAS Latency must be set
in the Mode Register at power-up.
When the Precharge Operation is performed on a bank during a Burst Read and operation, the
Burst operation is terminated.
When the Read with Auto-precharge command is issued, the Precharge operation is performed
automatically after the Read cycle, then the bank is switched to the idle state. This command
cannot be interrupted by any other commands. Refer to the diagrams for Read operation.
相關PDF資料 |
PDF描述 |
|---|---|
| W9425G6JB-5 | DDR DRAM, PBGA60 |
| W9425G8DH-6 | 32M X 8 DDR DRAM, 0.7 ns, PDSO66 |
| W946432AD-6 | 2M X 32 DDR DRAM, 0.1 ns, PQFP100 |
| W947D6HBHX6E | 8M X 16 DDR DRAM, 5 ns, PBGA60 |
| W9602BB | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 28VDC, PANEL MOUNT-THREADED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W9412G2IB-5 | 制造商:Winbond Electronics Corp 功能描述:8*16 DDR1 |
| W9412G6CH | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2M 】 4 BANKS 】 16 BITS DDR SDRAM |
| W9412G6IH | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2M × 4 BANKS × 16 BITS DDR SDRAM |
| W9412G6IH-5 | 功能描述:IC DDR-400 SDRAM 128MB 66TSSOPII RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.173"，4.40mm 寬） 供應商設備封裝:8-MFP 包裝:帶卷 (TR) |
| W9412G6JH | 制造商:WINBOND 制造商全稱:Winbond 功能描述:2M ? 4 BANKS ? 16 BITS DDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。