- 您現在的位置：買賣IC網 > PDF目錄373745 > TSS463D Industrial Control IC PDF資料下載
參數資料
| 型號： | TSS463D |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工業控制IC |
| 文件頁數： | 26/52頁 |
| 文件大小： | 268K |
| 代理商： | TSS463D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
TSS461C
26
Rev. D (22 Feb 01)
9.2.5. Line Status Register (0x04) :
7
6
5
4
3
2
1
0
SPG
IDG
Sc
Sb
Sa
TXG
RXG
Read only register.
Default value after reset : 0bx01xxx00.
This register reports the operation mode of the TSS461C in the Sleep an Idle bits (Command Register located at
address 0
×
03) as well as the diagnosis system status bits S2 to S0 discussed in section 8.
SPG
: Sleeping
IDG
: Idling.
Default mode at reset
Sa, Sb and Sc
: Diagnosis system status bits
Sa and Sb
Table 7. Diagnosis System Status Bits
Sb
Sa
COMMUNICATION INDICATION
0
0
Nominal mode, differential communication
0
1
Degraded over DATA, fault on DATA
1
0
Degraded over DATA, fault on DATA
1
1
Major error, fault on DATA and DATA
Sc
: As soon as one of the three inputs (RXD2, RXD1, RXD0) differs
from the others in the input comparison analysis performs by the
diagnosis system, S2 is set.
The only ways to reset this status bit are through the RI signal or a
general reset.
TXG
: Transmitting.
If this status bit is active, it indicates that the TSS461C has choosen an
identifier to transmit, and it will continue to make transmission attempt
for this message until it succeeds or the retry count is exceeded.
RXG
: Receiving.
The receiving indicates that there is activity on the bus.
NOTE : For safe modification of active channel registers both bits
should be inactive (except
“
abort
”
command).
9.2.6. Transmission Status Register (0x05) :
7
6
5
4
3
2
1
0
NRT3
NRT2
NRT1
NRT0
IDT3
IDT2
IDT1
IDT0
Read only register.
Default value after reset : 0x00.
The transmission Status register contains the number of retries made up-to-date, according to the Table 4. , and the
channel currently in transmission.
NRT [3:0]
: Number of retries done in transmission.
IDT [3:0]
: Channel number currently in transmission.
相關PDF資料 |
PDF描述 |
|---|---|
| TSS463R | Industrial Control IC |
| TSS461E | VAN Data Link Controller |
| TSS461E-TDRA-9 | VAN Data Link Controller |
| TSS461E-TERA-9 | VAN Data Link Controller |
| TSS461E-TRDZ-9 | VAN Data Link Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSS463R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| TSS463VAN | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Van Controller Serial Interface |
| TSS47 | 功能描述:瓷片電容器 100V 20% 0.047uF RoHS:否 制造商:Vishay/Cera-Mite 電容:0.01 uF 容差:20 % 電壓額定值:3 kV 工作溫度范圍:- 25 C to + 105 C 損耗因數 DF: 端接類型:Radial 產品:High Voltage Ceramic Disc Capacitors |
| TSS4B01G | 功能描述:整流器 4.0 Amp 50 Volt 150 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| TSS4B01G C2 | 制造商:SKMI/Taiwan 功能描述:Diode Rectifier Bridge Single 50V 4A 4-Pin TS4B Tube |
發布緊急采購，3分鐘左右您將得到回復。