- 您現在的位置：買賣IC網 > PDF目錄373745 > TSS463D Industrial Control IC PDF資料下載
參數資料
| 型號： | TSS463D |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工業控制IC |
| 文件頁數： | 25/52頁 |
| 文件大小： | 268K |
| 代理商： | TSS463D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
TSS461C
25
Rev. D (22 Feb 01)
ETIP
: Enable Transmission In Progress
One : Enable TIP generation
Zero : Disable TIP generation.
–
The Transmission In Progress (TIP), tells the diagnosis system to
enable transmission diagnosis.
ESDC
: Enable System Diagnosis Clock
One : Enable SDC divider.
Zero : Disable SDC divider.
–
The Synchronous Diagnosis Clock (SDC), controls the cycle time of
the synchronous diagnosis.
9.2.4. Command Register (0x03) :
7
6
5
4
3
2
1
0
GRES
SLEEP
IDLE
ACTI
REAR
0
0
MSDC
Write only register.
Reserved : Bit 1, 2 these bit must not be set by the user ; a zero must always be written to these bit.
If the circuit is operating at low birates there might be a considerable delay between the writing of this register and
the performing of the actual command (worst case 6 timeslots). The user is therefore recommanded to verify, by
reading the Line Status Register (0x04) that the commands have been performed.
GRES
: General Reset.
The Reset circuit command bit performs, if set, exactly as if the external
reset pin was asserted. This command bit has its own auto-reset circuitry.
One : Reset active
Zero : Reset inactive
SLEEP
: Sleep command.
If the user sets the Sleep bit, the circuit will enter sleep mode. When the
circuit is in sleep mode, all non-user registers are setup to minimize
power consumption and the oscillator is stopped. To exit from this mode
the user must set either the idle or activate commands.
One : Sleep active
Zero : Sleep inactive
IDLE
: Idle command.
If the user sets the Idle bit, the circuit will enter idle mode. In idle mode
the oscillator will operate, but the TSS461C will not transmit or receive
anything on the bus, and the TXD output will be in three state
One : Idle active
Zero : Idle inactive
ACTI
: Activate command.
The Activate command will put the circuit in the active mode, i.e it will
transmit and receive normally on the bus. When the circuit is in activate
mode the TXD three-state output is enabled.
One : Activate active
Zero : Activate inactive
REAR
: Re-Arbitrate command.
This command will, after the current attempt, reset the retry counter and
re-arbitrate the messages to be transmitted in order to find the highest
priority message to transmit.
One : Re-arbitrate active
Zero : Re-arbitrate inactive
MSDC
: Manual System Diagnosis Clock.
Rather than using the SDC divider described in section 9.2.3., the user
can use the manual SDC command to generate a SDC pulse for the
diagnosis system.
This MSDC pulse should be high at least two timeslot clock.
相關PDF資料 |
PDF描述 |
|---|---|
| TSS463R | Industrial Control IC |
| TSS461E | VAN Data Link Controller |
| TSS461E-TDRA-9 | VAN Data Link Controller |
| TSS461E-TERA-9 | VAN Data Link Controller |
| TSS461E-TRDZ-9 | VAN Data Link Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSS463R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| TSS463VAN | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Van Controller Serial Interface |
| TSS47 | 功能描述:瓷片電容器 100V 20% 0.047uF RoHS:否 制造商:Vishay/Cera-Mite 電容:0.01 uF 容差:20 % 電壓額定值:3 kV 工作溫度范圍:- 25 C to + 105 C 損耗因數 DF: 端接類型:Radial 產品:High Voltage Ceramic Disc Capacitors |
| TSS4B01G | 功能描述:整流器 4.0 Amp 50 Volt 150 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| TSS4B01G C2 | 制造商:SKMI/Taiwan 功能描述:Diode Rectifier Bridge Single 50V 4A 4-Pin TS4B Tube |
發布緊急采購，3分鐘左右您將得到回復。