- 您現在的位置：買賣IC網 > PDF目錄373745 > TSS463D Industrial Control IC PDF資料下載
參數資料
| 型號： | TSS463D |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工業控制IC |
| 文件頁數： | 12/52頁 |
| 文件大?。?/td> | 268K |
| 代理商： | TSS463D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
TSS461C
12
Rev. D (22 Feb 01)
VAN BUS
SEQUENCE
VAN BUS
SEQUENCE
VAN BUS
SEQUENCE
NUMBER OF
PRESCALED
CLOCKS
NRZ
“
0
”
NRZ
“
1
”
MANCHESTER
“
0
”
MANCHESTER
“
1
”
0
8
16
24
32
Figure 11. Data Encoding.
The IFS is defined to be a minimum of 64 prescaled clocks periods. The TSS461C, accepts an IFS of zero prescaled
clocks for the reception only of a SOF sequence.
Once the bus has been determined as being free, the module must now, if it is an autonomous module, emit a SOF
sequence or, if it is a synchronous access module, wait until it detects a preamble sequence.
Up till this point there can be several modules transmitting on the bus, and there is no possibility of knowing if this
is the case or not. Therefore the first field in wich arbitration can be performed is the identifier field. Since the logical
zeroes on the bus are dominant, and all data is transmitted with the most significant bit (MSB) first, the first module
to transmit a logical zero on the bus will be the prioritized module, i.e. the message that is tagged with the lowest
identifier will have priority over the other messages.
It is, however, conceivable that two messages transmitted on the bus will have the same identifier. The TSS461C
therefore continues the arbitration of the bus throughout the whole frame. More, if the identifier in transmission has
been programmed for reception as well, it transmits and receives messages simultaneously, right up till the Frame
Check Sequence (FCS). Only then, if the TSS461C has transmitted the whole message, does it discard the message
received. Arbitration loss in the FCS field is considered as a CRC error during transmission.
This feature is called full data field arbitration, and it enables the user to extend the identifier. For instance it can be
used to transmit the emitting modules address in the first bytes of the data field, thus enabling the identifier to specify
the contents of the frame and the data field to specify the source of the information.
The identifier field of the VAN bus frame is always 12 bits long, and it is always followed immediately by the 4-bit
command field:
The first bit of the command is the extension bit (EXT). This bit is defined by the user on transmission and is
received and retained by the TSS461C. To conform with the standard it should be set to 1 (recessive) by the user,
else the frame is ignored without any IT generation.
The second bit is the request ACKnowledge bit (RAK). If this bit is a logical one, the receiving module must
acknowledge the transfer with an in-frame acknowledgement in the ACK field. If it is set to logical zero, then the
ACK field must contain an acknowledge absent sequence.
Third we have the Read/Write bit (R/W). This bit indicates the direction of the data in a frame.
If set to zero it is a
“
write
”
message, i.e. data transmitted by one module to be received by another module.
If it is set to one it implies a
“
read
”
message, i.e. a request that another module should transmit data to be received
by the one that requested the data (reply request message).
Last in the command field is the Remote Transmission Request bit (RTR). This bit is a logical zero if the frame
contains data and a logical one if the frame does not contain data. In order to conform with the standard a received
frame included the comination R/W. RTR = 01 is ignored without any IT generation.
相關PDF資料 |
PDF描述 |
|---|---|
| TSS463R | Industrial Control IC |
| TSS461E | VAN Data Link Controller |
| TSS461E-TDRA-9 | VAN Data Link Controller |
| TSS461E-TERA-9 | VAN Data Link Controller |
| TSS461E-TRDZ-9 | VAN Data Link Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSS463R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| TSS463VAN | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Van Controller Serial Interface |
| TSS47 | 功能描述:瓷片電容器 100V 20% 0.047uF RoHS:否 制造商:Vishay/Cera-Mite 電容:0.01 uF 容差:20 % 電壓額定值:3 kV 工作溫度范圍:- 25 C to + 105 C 損耗因數 DF: 端接類型:Radial 產品:High Voltage Ceramic Disc Capacitors |
| TSS4B01G | 功能描述:整流器 4.0 Amp 50 Volt 150 Amp IFSM RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| TSS4B01G C2 | 制造商:SKMI/Taiwan 功能描述:Diode Rectifier Bridge Single 50V 4A 4-Pin TS4B Tube |
發布緊急采購，3分鐘左右您將得到回復。