- 您現在的位置：買賣IC網 > PDF目錄385945 > TPS2306EVM-001 (Texas Instruments, Inc.) TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) PDF資料下載
參數資料
| 型號： | TPS2306EVM-001 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) |
| 中文描述： | TPS2306熱插拔雙測序電源管理評估模塊和接口卡（雙序列熱交換電源管理器件TPS2306的評估板與接口卡） |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 462K |
| 代理商： | TPS2306EVM-001 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
SLUU094
3
TPS2306 Dual Sequencing Hot Swap Power Manager
1
Introduction
This User’s Guide describes the use and operating features of the TPS2306 evaluation module (EVM). The
Texas Instruments (TI) TPS2306 is a dual channel hot-swap power manager with programmable output
sequencing control. It integrates inrush current control, electronic circuit breaker, power-up and power-down
sequencing and fault indication functions to provide plug-in module designers with a configurable hot swap
solution. The TPS2306 EVM is a PCB-based tool used to evaluate the performance of the device in simulated
live insertion and removal actions.
1.1
Features
The following list highlights some of the features of the TPS2306.
Wide Input Operating Range: 2.75 V to 13.6 V
Controls Ramp-Up Sequence and Slope
Controls Ramp-Down Sequence
Controls Inrush Current
Precise Linear Current Amplifier
Programmable Overcurrent Threshold
Programmable Soft-Start Capability and Fault Timer
Internal Charge Pump to Drive Low-Cost External N-Channel MOSFETs
Cascadable for Three or More Supplies
Fault Indicator Output
Remote Shutdown/Enable Control
1.2
Description
The TPS2306 provides hot swap control, fault handling and sequencing of two positive voltage supplies. The
input supply operating range of 2.75 V to 13.6 V makes the TPS2306 applicable in numerous digital and
signaling applications.
The TPS2306 operates in conjunction with two external N-channel MOSFETs to limit inrush current, and control
output sequencing and slope during live insertion events, while creating a low impedance interface between
supply and load after insertion transients have passed. An on-chip linear current amplifier (LCA) provides
closed-loop control of the current sourced to the load circuitry during hot swap. An internal charge pump boosts
the Channel 1 input supply to fully enhance the MOSFETs under subsequent steady-state loading conditions.
A second level of power bus protection is provided by fast over-current comparators monitoring the load current
levels of each channel. In a short-circuit event, the overcurrent comparators will rapidly latch off both N-channel
MOSFETs.
A high degree of user programmability allows configuration of the TPS2306 over a wide range of load
characteristics. Control inputs allow the module designer to set the maximum current level and inrush current
profile (slew rate) during module start-up. Under fault conditions, an on-chip timer controls how long the HSPM
is allowed to operate in current-control mode prior to turning off the pass elements. Timer duration is easily
programmed with a single external capacitor.
Supply sequencing control is implemented via four comparator inputs to independently control the ramp-up and
ramp-down of each supply output. A TTL- and CMOS-compatible enable input allows system-level control of
the output status and selection of the low-power sleep mode. The open-drain FAULT output provides single line
fault reporting to the system host or controller.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2310PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2311PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2320D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2320PW | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2321D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS230QP | 制造商:Texas Instruments 功能描述: |
| TPS2310IPW | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWR | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWRG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。