- 您現在的位置：買賣IC網 > PDF目錄385945 > TPS2306EVM-001 (Texas Instruments, Inc.) TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) PDF資料下載
參數資料
| 型號： | TPS2306EVM-001 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) |
| 中文描述： | TPS2306熱插拔雙測序電源管理評估模塊和接口卡（雙序列熱交換電源管理器件TPS2306的評估板與接口卡） |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 462K |
| 代理商： | TPS2306EVM-001 |
SLUU094
11
TPS2306 Dual Sequencing Hot Swap Power Manager
3
Getting Started
3.1
Equipment Requirements
The following test equipment is required to use the TPS2306 hot swap EVM.
Power supply, 5 V
DC
at 3 amps minimum
Power supply, 3.3 V
DC
at 5 amps minimum
Oscilloscope
Digital voltmeter
3.2
Verifying the EVM Operation
3.2.1
Equipment Setup
Turn on the power supplies. Set one of the supply outputs to 5 V
DC
, and the other to 3.3 V
DC
.
On the interface card, place switch S1 in the LO position. On the hot swap EVM, place the individual DIP switches
of S1 in the positions shown in Table 6.
Table 6. EVM Switch S1 Initial Positions
SWITCH
POSITION
S1
–
1
OFF
S1
–
2
X
S1
–
3
ON
S1
–
4
ON
Install jumpers across terminals JP1, JP2, JP3, and JP4. Insert the hot swap EVM board into the P1 edge
connector on the interface card, observing the insertion keying. Connect the power supplies, EVM boards, and
oscilloscope as shown in Figure 5.
+5.0V P/S
+
–
OSCILLO
–
SCOPE
CH2
CH 1
CH3
SLVP155
INTERFACE
CARD ASSY
SLUP056
HOT SWAP EVM
ASSEMBLY
TP11
TP3
TP14
TP4
P1
P1
+3.3V P/S
+
–
VIN1
GND
VIN2
GND
Figure 5. Equipment Setup
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2310PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2311PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2320D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2320PW | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2321D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS230QP | 制造商:Texas Instruments 功能描述: |
| TPS2310IPW | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWR | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWRG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。