參數資料
型號: TPS2306EVM-001
廠商: Texas Instruments, Inc.
元件分類: 基準電壓源/電流源
英文描述: TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡)
中文描述: TPS2306熱插拔雙測序電源管理評估模塊和接口卡(雙序列熱交換電源管理器件TPS2306的評估板與接口卡)
文件頁數: 10/19頁
文件大?。?/td> 462K
代理商: TPS2306EVM-001
SLUU094
10
TPS2306 Dual Sequencing Hot Swap Power Manager
2.3
TPS2306 EVM Kit Operating Specifications
Component selection for the TPS2306 EVM was done to configure the circuit for the input and load conditions
shown in Table 4. Therefore, these parameters describe the intended operating conditions of the module.
Current limit and fault timeout options were determined using the nominal load currents shown. In addition, the
load electronics were assumed to have the minimum Under Voltage Lockout (UVLO) thresholds shown. Instead
of UVLO protection, another applicable implementation would be one in which the load electronics are held in
reset for at least the period of the supply voltage ramps.
Table 4. Evaluation Module Design Parameters
PARAMETER
MIN
NOM
MAX
UNITS
Operating temperature range
40
85
C
Supply voltage 1 (VIN1)
5.0
±
10
3.3
±
5
VDC
Tolerance on VIN1
%
Supply voltage 2 (VIN2)
VDC
Tolerance on VIN2
%
UVLO threshold, channel 1 load
4.0
VDC
UVLO threshold, channel 2 load
3.0
VDC
Channel 1 load current
0.5
A
Channel 2 load current
NOTES:
2.0
A
1. All voltages are with respect to the PCB GND node.
2. Currents are positive into and negative out of the specified terminal.
3. Channel 1 load current is limited by installed value and rating of resistor R1.
The TPS2306 EVM was designed with a high degree of user-programmability, as described in Section 4
(Reconfiguring the EVM). This includes modifications for different input voltage and load current conditions.
However, under no circumstances should the EVM be operated beyond the input supply or load current levels
specified in Table 5.
Table 5. EVM Absolute Maximum Ratings
PARAMETER
NODE
MIN
MAX
UNITS
Supply voltage 1
VIN1
4
13.6
V
Supply voltage 2
VIN2
3
13.6
V
Channel 1 output (load) current
VOUT1
4.2
A
Channel 2 output (load) current
NOTES:
1. All voltages are with respect to the PCB GND node.
2. Currents are positive into and negative out of the specified terminal.
3. Channel 1 load current is limited by installed value and rating of resistor R1.
VOUT2
7.0
A
相關PDF資料
PDF描述
TPS2310PW DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2311PW DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING
TPS2320D DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2320PW DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2321D DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
相關代理商/技術參數
參數描述
TPS230QP 制造商:Texas Instruments 功能描述:
TPS2310IPW 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2310IPWG4 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2310IPWR 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2310IPWRG4 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube