- 您現在的位置：買賣IC網 > PDF目錄385945 > TPS2306EVM-001 (Texas Instruments, Inc.) TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) PDF資料下載
參數資料
| 型號： | TPS2306EVM-001 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | TPS2306 Dual Sequencing Hot Swap Power Manager Evaluation Module and Interface Card(雙序列熱交換電源管理器件TPS2306的評估板與接口卡) |
| 中文描述： | TPS2306熱插拔雙測序電源管理評估模塊和接口卡（雙序列熱交換電源管理器件TPS2306的評估板與接口卡） |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 462K |
| 代理商： | TPS2306EVM-001 |
SLUU094
17
TPS2306 Dual Sequencing Hot Swap Power Manager
4.6
Configuring the EVM for High Voltage Applications
The TPS2306 EVM can be easily configured for high voltage applications, up to 13.6 V maximum supply input.
For these applications, two steps must be taken.
1.
Set the fault timing, sequencing, and IMAX component values for the targeted supplies and load
characteristics, as described in Sections 4.1
–
4.4.
2.
For applications where the Channel 1 supply is greater than 6.5 V (e.g., 10-V or 12-V systems), remove
resistor R25 and replace it with a 1-k
, SMD 1210-size resistor.
4.7
Automatic Power-Up
The TPS2306 EVM and interface card can be set up to bring up the supply outputs automatically after board
insertion. The following two steps will select an autonomous power-up mode of operation.
1.
On the hot swap EVM, set switch S1-1 in the ON position.
2.
Remove resistor R1 from the interface card. R1 is located near switch S1 (refer to Figure 3). Place switch
S1 in the HI position.
The EVM now brings up the outputs automatically when it is inserted into the interface card
’
s P1 connector. To
create a short start-up delay from insertion, install an appropriate value, 0805-size capacitor at C19 on the EVM
card.
For proper operation of the supply turnoff sequencing, the TPS2306 device itself must remain powered up during
the shutdown event. To observe operation of this function, return switch S1-1 to the OFF position prior to PCB
removal from the interface card.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2310PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2311PW | DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING |
| TPS2320D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2320PW | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
| TPS2321D | DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS230QP | 制造商:Texas Instruments 功能描述: |
| TPS2310IPW | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWR | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2310IPWRG4 | 功能描述:熱插拔功率分布 3-13V Dual w/Intrdpt Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。