- 您現在的位置：買賣IC網 > PDF目錄365566 > SII3114_07 (Silicon Image, Inc.) PCI to Serial ATA Controller PDF資料下載
參數資料
| 型號： | SII3114_07 |
| 廠商： | Silicon Image, Inc. |
| 英文描述： | PCI to Serial ATA Controller |
| 中文描述： | PCI到Serial ATA控制器 |
| 文件頁數： | 82/127頁 |
| 文件大?。?/td> | 598K |
| 代理商： | SII3114_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁
SiI
3114 PCI to Serial ATA Controller
Data Sheet
Silicon Image, Inc.
SiI
-DS-0103-D
74
2007 Silicon Image, Inc.
Programming Sequences
The programming sequence for the
SiI
3114 is about the same as for the
SiI
3112 or
SiI
3512. However,
SiI
3114
supports up to four SATA devices (instead of two for the others).
In order to minimize the legacy BIOS code changes, the
SiI
3114 uses “Master/Slave” type of emulation for the
register mapping of Base Address Register 0 ~ 4 (between SATA device 0 and device 2 or SATA device 1 and
device 3). Therefore, the programmer will not be able to access SATA device 0 and device 2 (or device 1 and
device 3) at the same time when BAR 0~4 are used to access the devices. SATA device 0 is equivalent to legacy
Primary Master device, SATA device 1 is equivalent to legacy Secondary Master device, SATA device 2 is
equivalent to legacy Primary Slave device, and SATA device 3 is equivalent to legacy Secondary Slave device.
In order to access all four SATA devices simultaneously, BAR5 registers must be used. They have a similar
structure to the previous 2 channel controllers for the first 512 bytes (for device 0 and device 1), but they have an
additional 512 bytes of registers to duplicate the register structures for the additional two SATA channels (device 2
and device 3).
When BAR5 registers are used to access all four SATA devices simultaneously, the interrupt steering bit at bit 1 in
BAR5 offset 200h must be set. The interrupt steering bit must be reset when “Master/Slave” type of emulation is
used. The reset value for this bit is 0.
This bit must be remained set for simultaneous 4 channels operation. Any
write operation to the BAR5 offset 200h register should mask the "Interrupt steering" bit and not to reset it by
accident.
Recommended Initialization Sequence for the
SiI
3114
The recommended initialization sequence for the
SiI
3114 is detailed below.
Initialize PCI Configuration Space registers:
Initialize Base Address Register 0 with the address of an 8-byte range in I/O space.
Initialize Base Address Register 1 with the address of a 4-byte range in I/O space.
Initialize Base Address Register 2 with the address of an 8-byte range in I/O space.
Initialize Base Address Register 3 with the address of a 4-byte range in I/O space.
Initialize Base Address Register 4 with the address of a 16-byte range in I/O space.
Initialize Base Address Register 5 with the address of a 1024-byte range in memory space.
To enable the bios expansion ROM, initialize the Expansion ROM Base Address Register with the address
of a 512KB range in memory space.
Enable I/O space access, memory space access, and bus master operation by setting bits [2:0] of the PCI
Command register.
Note:
The preceding configuration space register initialization is normally done by the motherboard BIOS in PC
type systems.
If the arbiter’s default FIFO read/write request thresholds are not suitable for the application they may be changed
via the FIFO Valid Byte Count and Control Channel x register. The read threshold is defined by bits [05:00], and
the write threshold is defined by bits [13:08] in the FIFO Valid Byte Count and Control – Channel x register. In
most environments, setting these bit fields to zero results in the best utilization of the PCI bus by the
SiI
3114
controller.
If interrupt driven operation is
not
desired, set bits [23:22] of the System Configuration Status and Command
register to block interrupts from reaching the PCI bus.
相關PDF資料 |
PDF描述 |
|---|---|
| SiI3114CT176 | PCI to Serial ATA Controller |
| SiI3114CTU | PCI to Serial ATA Controller |
| SII3124A | PCI-X to Serial ATA Controller |
| SiI3124ACBHU | PCI-X to Serial ATA Controller |
| SII3132 | PCI Express to 2-Port Serial ATA II Host Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SII3114CT176 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI to Serial ATA Controller |
| SII3114CTU | 制造商:Silicon Image Inc 功能描述:PCI to Serial ATA Controller 176-Pin TQFP 制造商:SILICON 功能描述: |
| SII3124A | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3124ACBHU | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI-X to Serial ATA Controller |
| SII3132 | 制造商:SILICONIMAGE 制造商全稱:SILICONIMAGE 功能描述:PCI Express to 2-Port Serial ATA II Host Controller |
發布緊急采購，3分鐘左右您將得到回復。