- 您現在的位置：買賣IC網 > PDF目錄365432 > S71GL256NB0 (Spansion Inc.) Stacked Multi-chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71GL256NB0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 56/147頁 |
| 文件大?。?/td> | 1655K |
| 代理商： | S71GL256NB0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
56
S29GLxxxN MirrorBit
TM
Flash Family
S29GLxxxN_00_A4 June 14, 2004
A d v a n c e I n f o r m a t i o n
After the Program Resume command is written, the device reverts to program-
ming. The system can determine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard program operation. See Write Op-
eration Status for more information.
The system must write the Program Resume command (address bits are don’t
care) to exit the Program Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ignored. Another Program
Suspend command can be written after the device has resume programming.
Figure 3. Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is ini-
tiated by writing two unlock cycles, followed by a set-up command. Two
additional unlock write cycles are then followed by the chip erase command,
which in turn invokes the Embedded Erase algorithm. The device does
not
require
the system to preprogram prior to erase. The Embedded Erase algorithm auto-
matically preprograms and verifies the entire memory for an all zero data pattern
prior to electrical erase. The system is not required to provide any controls or tim-
ings during these operations. Table
10
and Table
11
show the address and data
requirements for the chip erase command sequence.
When the Embedded Erase algorithm is complete, the device returns to the read
mode and addresses are no longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6, or DQ2. Refer to the Write Operation
Status section for information on these status bits.
Program Operation
or Write-to-Buffer
Sequence in Progress
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Write Program Resume
Command Sequence
Read data as
required
Done
reading
No
Yes
Write address/data
XXXh/3030h
Device reverts to
operation prior to
Program Suspend
Write address/data
XXXh/B0B0h
Wait 15
μ
s
相關PDF資料 |
PDF描述 |
|---|---|
| S71GL512NB0 | Stacked Multi-chip Product (MCP) |
| S71GS256NC0BFWAK0 | 128N based MCPs |
| S71GS128NB0 | 128N based MCPs |
| S71GS128NB0BAWAK0 | 128N based MCPs |
| S71GS128NB0BAWAK2 | 128N based MCPs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71GL256NC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL512NB0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL512NC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL-N | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL-N_08 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
發布緊急采購，3分鐘左右您將得到回復。