- 您現在的位置：買賣IC網 > PDF目錄365432 > S71GL256NB0 (Spansion Inc.) Stacked Multi-chip Product (MCP) PDF資料下載
參數資料
| 型號： | S71GL256NB0 |
| 廠商： | Spansion Inc. |
| 英文描述： | Stacked Multi-chip Product (MCP) |
| 中文描述： | 堆疊式多芯片產品（MCP） |
| 文件頁數： | 51/147頁 |
| 文件大?。?/td> | 1655K |
| 代理商： | S71GL256NB0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁
June 14, 2004 S29GLxxxN_00_A4
S29GLxxxN MirrorBit
TM
Flash Family
51
A d v a n c e I n f o r m a t i o n
to an address that is either in the read or erase-suspend-read mode. The autose-
lect command may not be written while the device is actively programming or
erasing.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system may read at any address any
number of times without initiating another autoselect command sequence:
A read cycle at address XX00h returns the manufacturer code.
Three read cycles at addresses 01h, 0Eh, and 0Fh return the device code.
A read cycle to an address containing a sector address (SA), and the address
02h on A7–A0 in word mode returns 01h if the sector is protected, or 00h if
it is unprotected.
The system must write the reset command to return to the read mode (or erase-
suspend-read mode if the device was previously in Erase Suspend).
Enter Secured Silicon Sector/Exit Secured Silicon
Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-
word/16-byte random Electronic Serial Number (ESN). The system can access
the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon
Sector command sequence. The device continues to access the Secured Silicon
Sector region until the system issues the four-cycle Exit Secured Silicon Sector
command sequence. The Exit Secured Silicon Sector command sequence returns
the device to normal operation. Table
10
and Table
11
show the address and data
requirements for both command sequences. See also “Secured Silicon Sector
Flash Memory Region” for further information.
Note that the ACC function and un-
lock bypass modes are not available when the Secured Silicon Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the program set-up com-
mand. The program address and data are written next, which in turn initiate the
Embedded Program algorithm. The system is
not
required to provide further con-
trols or timings. The device automatically provides internally generated program
pulses and verifies the programmed cell margin. Table
10
and Table
11
show the
address and data requirements for the word program command sequence.
When the Embedded Program algorithm is complete, the device then returns to
the read mode and addresses are no longer latched. The system can determine
the status of the program operation by using DQ7 or DQ6. Refer to the Write Op-
eration Status section for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm
are ignored.
Note that the Secured Silicon Sector, autoselect, and CFI
functions are unavailable when a program operation is in progress.
Note
that a
hardware reset
immediately terminates the program operation. The pro-
gram command sequence should be reinitiated once the device has returned to
the read mode, to ensure data integrity.
Programming is allowed in any sequence and across sector boundaries. Program-
ming to the same word address multiple times without intervening erases is
limited. For such application requirements, please contact your local Spansion
representative.
Any word cannot be programmed from “0” back to a “1.”
Attempting to do so may cause the device to set DQ5 = 1, or cause the DQ7 and
相關PDF資料 |
PDF描述 |
|---|---|
| S71GL512NB0 | Stacked Multi-chip Product (MCP) |
| S71GS256NC0BFWAK0 | 128N based MCPs |
| S71GS128NB0 | 128N based MCPs |
| S71GS128NB0BAWAK0 | 128N based MCPs |
| S71GS128NB0BAWAK2 | 128N based MCPs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S71GL256NC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL512NB0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL512NC0 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP) |
| S71GL-N | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
| S71GL-N_08 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM |
發布緊急采購，3分鐘左右您將得到回復。