參數資料
型號： S71GL128NB0
廠商： Spansion Inc.
英文描述： Stacked Multi-chip Product (MCP)
中文描述： 堆疊式多芯片產品（MCP）
文件頁數： 52/147頁
文件大小： 1655K
代理商： S71GL128NB0
52
S29GLxxxN MirrorBit
TM
Flash Family
S29GLxxxN_00_A4 June 14, 2004
A d v a n c e I n f o r m a t i o n
DQ6 status bits to indicate the operation was successful. However, a succeeding
read will show that the data is still “0.” Only erase operations can convert a “0”
to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program words to the device
faster than using the standard program command sequence. The unlock bypass
command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle containing the unlock bypass command, 20h. The device
then enters the unlock bypass mode. A two-cycle unlock bypass program com-
mand sequence is all that is required to program in this mode. The first cycle in
this sequence contains the unlock bypass program command, A0h; the second
cycle contains the program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two unlock cycles required
in the standard program command sequence, resulting in faster total program-
ming time. Table
10
and Table
11
show the requirements for the command
sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (See Table
10
and Table
11
).
Write Buffer Programming
Write Buffer Programming allows the system write to a maximum of 16 words/32
bytes in one programming operation. This results in faster effective programming
time than the standard programming algorithms. The Write Buffer Programming
command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle containing the Write Buffer Load command written at the
Sector Address in which programming will occur. The fourth cycle writes the sec-
tor address and the number of word locations, minus one, to be programmed. For
example, if the system will program 6 unique address locations, then 05h should
be written to the device. This tells the device how many write buffer addresses
will be loaded with data and therefore when to expect the Program Buffer to Flash
command. The number of locations to program cannot exceed the size of the
write buffer or the operation will abort.
The fifth cycle writes the first address location and data to be programmed. The
write-buffer-page is selected by address bits A
MAX
–A
4
. All subsequent address/
data pairs must fall within the selected-write-buffer-page. The system then
writes the remaining address/data pairs into the write buffer. Write buffer loca-
tions may be loaded in any order.
The write-buffer-page address must be the same for all address/data pairs loaded
into the write buffer. (This means Write Buffer Programming cannot be performed
across multiple write-buffer pages. This also means that Write Buffer Program-
ming cannot be performed across multiple sectors. If the system attempts to load
programming data outside of the selected write-buffer page, the operation will
abort.)
Note that if a Write Buffer address location is loaded multiple times, the address/
data pair counter will be decremented for every data load operation. The host
system must therefore account for loading a write-buffer location more than
once. The counter decrements for each data load operation, not for each unique
write-buffer-address location. Note also that if an address location is loaded more
相關PDF資料
PDF描述
S71GL256NB0 Stacked Multi-chip Product (MCP)
S71GL512NB0 Stacked Multi-chip Product (MCP)
S71GS256NC0BFWAK0 128N based MCPs
S71GS128NB0 128N based MCPs
S71GS128NB0BAWAK0 128N based MCPs
相關代理商/技術參數
參數描述
S71GL128NC0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GL256NB0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GL256NC0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GL512NB0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
S71GL512NC0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Product (MCP)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*