- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335QFAAB (APPLIEDMICRO INC) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335QFAAB |
| 廠商： | APPLIEDMICRO INC |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI BUS CONTROLLER, PQFP176 |
| 封裝： | LQFP-176 |
| 文件頁數： | 23/189頁 |
| 文件大?。?/td> | 1193K |
| 代理商： | S5335QFAAB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 23
NON-VOLATILE MEMORY INTERFACE
SIGNALS
This signal grouping provides for connection to exter-
nal non-volatile memories. Either a serial or byte-wide
device may be used.
The serial interface shares the read and write control
pins used for interfacing with byte-wide memory
devices. Since it is intended that only one (serial or
byte wide) configuration be used in any given imple-
mentation, separate descriptions are provided for
each. The S5335 provides the pins necessary to inter-
face to a byte wide non-volatile memory. When they
are connected to a properly configured serial memory,
these byte wide interface pins assume alternate func-
tions. These alternate functions include added
external FIFO status flags, FIFO reset control, Add-On
control for bus mastering and a hardware interface
mailbox port..
Table 10. Serial nv Devices
Signal
Type
Description
SCL
out
Serial Clock. This output is intended to drive a two-wire Serial Interface and functions as the bus’s master.
It is intended that this signal be directly connected to one or more inexpensive serial non-volatile RAMs or
EEPROMs. This pin is shared with the byte wide interface signal, ERD#.
SDA
t/s
Serial Data/Address. This bidirectional pin is used to transfer addresses and data to or from a serial
nvRAM or EEPROM. It is an open drain output and intended to be wire-ORed with all other devices on the
serial bus using a 4.7K external pull-up resistor. This pin is shared with the byte wide interface signal,
EWR#.
SNV
in
Serial Non-Volatile Device. This input, when high, indicates a serial boot device or no boot device is
present. When this pin is low, a byte-wide boot device is present.
Table 11. Byte-Wide nv Devices
Signal
Type
Description
EA[15:00]
out
External nv memory address. These signals connect directly to the external BIOS (or EEPROM) or
EPROM address pins EA0 through EA15. The PCI interface controller assembles 32-bit-wide accesses
through multiple read cycles of the 8-bit device. The address space from 0040h through 007Fh is used
to preload and initialize the PCI configuration registers. Should an external nv memory be used, the
minimum size required is 128 bytes and the maximum is 64K bytes. When a serial memory is con-
nected to the S5335, the pins EA[7:0] are reconfigured to become a hardware Add-On to PCI mailbox
register with the EA8 pin as the mailbox load clock. Also, the EA15 signal pin will provide an indication
that the PCI to Add-On FIFO is full (FRF#), and the EA14 signal pin will indicate whether the Add-On to
PCI FIFO is empty (FWE#).
ERD#
out
External nv memory read control. This pin is asserted during read operations involving the external
non-volatile memory. Data is transferred into the S5335 during the low to high transition of ERD#. This
pin is shared with the serial external memory interface signal, SCL.
EWR#
t/s
External nv memory write control. This pin is asserted during write operations involving the external
non-volatile memory. Data is presented on pins EQ[7:0] along with its address on pins EA[15:0]
throughout the entire assertion of EWR#. This pin is shared with the serial external memory interface
signal, SDA.
EQ[7:0]
t/s
External memory data bus. These pins are used to directly connect with the data pins of an external
non-volatile memory. When a serial memory is connected to the S5335, the pins EQ4, EQ5, EQ6 and
EQ7 become reconfigured to provide signal pins for bus mastering control from the Add-On interface.
相關PDF資料 |
PDF描述 |
|---|---|
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
| S5566J | GENERAL PURPOSE RECTIFIER APPLICATIONS |
| S5566N | GENERAL PURPOSE RECTIFIER APPLICATIONS |
| S5688B | TOSHIBA Rectifier Silicon Diffused Type |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S533-M04-F13-F | 制造商:UNICORP 功能描述: |
| S5340 | 制造商:BOTHHAND 制造商全稱:Bothhand USA, LP. 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| S5342 | 制造商:MERKLE-KORFF INDUSTRIES 功能描述:Old Colman P/N: RP4-8 |
發布緊急采購，3分鐘左右您將得到回復。