- 您現在的位置：買賣IC網 > PDF目錄374668 > S5335 (Applied Micro Circuits Corp.) PCI Bus Controller, 3.3V PDF資料下載
參數資料
| 型號： | S5335 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PCI Bus Controller, 3.3V |
| 中文描述： | PCI總線控制器，3.3 |
| 文件頁數： | 111/189頁 |
| 文件大?。?/td> | 1193K |
| 代理商： | S5335 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁當前第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
S5335 – PCI Bus Controller, 3.3V
Revision 5.01 – November 30, 2005
Data Sheet
AMCC Confidential and Proprietary
DS1657 111
Mailbox Interrupts
Mailboxes can be configured to generate Add-On
interrupts (IRQ#) and/or allow the Add-On to generate
PCI interrupts (INTA#). Mailbox empty/full status con-
ditions be can used to interrupt the Add-On or PCI
host to indicate some action is required. An individual
mailbox byte is selected to generate an interrupt when
accessed. An outgoing mailbox becoming empty or an
incoming mailbox becoming full asserts the interrupt
output (if enabled).
When used with a serial nv memory boot device, the
mailboxes also provide a way to generate PCI inter-
rupts (INTA#) through hardware. When a serial nv
memory boot device is used, the device pin functions
EA0 - EA8 are redefined. These pins then provide
direct, external access to the Add-On outgoing mail-
box 4, byte 3 (which is also PCI incoming mailbox 4,
byte 3).
FIFO BUS INTERFACE
The FIFO register on the Add-On interface may only
be accessed synchronously or asynchronously. Asyn-
chronous burst read and write FIFO operations are not
recommended. Location 45h, bits 6 and 5 in the nv
memory boot device must be programmed to a “0” for
correct operation.
FIFO Direct Access Inputs
RDFIFO# and WRFIFO# are referred to as FIFO
‘direct access’ inputs. Asserting RDFIFO# is function-
ally identical to accessing the FIFO with RD#,
SELECT#, BE[3:0]#, and ADR[6:2]. Asserting
WRFIFO# is functionally identical to accessing the
FIFO with WR#, SELECT#, BE[3:0]#, and ADR[6:2].
RD# and WR# must be deasserted when RDFIFO# or
WRFIFO# is asserted, but SELECT# may be
asserted. These inputs automatically drive the address
(internally) to 20h and assert all byte enables. The
ADR[6:2] and BE[3:0]# inputs are ignored when using
the FIFO direct access inputs. RDFIFO# and
WRFIFO# are useful for Add-On designs which cas-
cade an external FIFO into the S5335 FIFO or use
dedicated external logic to access the FIFO.
Direct access signals always access the FIFO as 16-
bits or 32-bits, whatever the MODE pin is configured
for. For 16-bit mode, two consecutive accesses fill or
empty the 32-bit FIFO register.
FIFO Status Signals
The FIFO Status signals indicate to the Add-On logic
the current state of the S5335 FIFO. A FIFO status
change caused by a PCI FIFO access is reflected one
PCI clock period after the PCI access is completed
(TRDY# asserted). A FIFO status change caused by
an Add-On FIFO access is reflected immediately (after
a short propagation delay) after the access occurs. For
Add-On accesses, FIFO status is updated after the ris-
ing edge of BPCLK for synchronous interfaces or after
the rising edge of the read or write strobe for asyn-
chronous interfaces.
FIFO Control Signals
For Add-On initiated PCI bus mastering, the FIFO sta-
tus reset controls FWC# (Add-On to PCI FIFO clear)
and FRC# (PCI to Add-On FIFO clear) are available.
FWC# and FRC# must be asserted for a minimum of
one BPCLK period to be recognized. These inputs are
sampled at the rising edge of BPCLK. These inputs
should not be asserted unless the FIFO is idle. Assert-
ing a FIFO status reset input during a PCI or Add-On
FIFO access results in indeterminate operation.
For Add-On initiated bus master transfers, AMREN
(Add-On bus master read enable) and AMWEN (Add-
On bus master write enable) are used, in conjunction
with the appropriate FIFO status signals, to enable the
S5335 to assert its PCI bus request (REQ#).
PASS-THRU BUS INTERFACE
The S5335 Pass-Thru interface is synchronous. The
Add-On Pass-Thru Address (APTA) and Add-On
Pass-Thru Data (APTD) registers may be accessed
pseudo-synchronously.
Although BPCLK is used to clock data into and out of
the Pass-Thru registers, accesses may be performed
asynchronously. For reads, APTA or APTD data
remains valid as long as RD# (or PTADR#) is
asserted. A new value is not driven until PTRDY# is
asserted by Add-On logic. For writes to APTD, data is
clocked into the S5335 on every BPCLK rising edge,
but is not passed to the PCI bus until PTRDY# is
asserted. PTRDY# must by synchronized to BPCLK.
Pass-Thru Status Indicators
The Pass-Thru status indicators indicate that a Pass-
Thru access is in process and what action is required
by the Add-On logic to complete the access. All Pass-
Thru status indicators are synchronous with the PCI
clock.
Pass-Thru Control Inputs
Some Pass-Thru implementations may require an
address corresponding to the Pass-Thru data. The
Add-On Pass-Thru Address Register (APTA) contains
the PCI address for the Pass-Thru cycle. To allow
access to the Pass-Thru address without generating
an Add-On read cycle, PTADR# is provided. PTADR#
is a direct access input for the Pass-Thru address.
相關PDF資料 |
PDF描述 |
|---|---|
| S5335DK | PCI Bus Controller, 3.3V |
| S5335QF | PCI Bus Controller, 3.3V |
| S5335QFAAB | PCI Bus Controller, 3.3V |
| S5566B | General Purpose Rectifier(通用整流器) |
| S5566G | General Purpose Rectifier(通用整流器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S5335DK | 制造商:AMCC 制造商全稱:Applied Micro Circuits Corporation 功能描述:PCI Bus Controller, 3.3V |
| S5335QF | 制造商:AppliedMicro 功能描述: |
| S5335QFAAB | 制造商:AppliedMicro 功能描述:PCI Bus Controller |
| S533-M04-F13A-E | 制造商:UNICORP 功能描述: |
| S-533-M04-F13-F | 制造商:UNICORP 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。