參數資料
型號： S29GL128N10FAI010
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
中文描述： 8M X 16 FLASH 3V PROM, 100 ns, PBGA64
封裝： 13 X 11 MM, FBGA-64
文件頁數： 57/100頁
文件大小： 952K
代理商： S29GL128N10FAI010
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit Flash Family
55
D a t a S h e e t
Figure 2. Program Operation
Program Suspend/ Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or
a Write to Buffer programming operation so that data can be read from any non-suspended
sector. When the Program Suspend command is written during a programming process, the
device halts the program operation within 15 μs maximum (5
μs typical) and updates the sta-
tus bits. Addresses are not required when writing the Program Suspend command.
After the programming operation is suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a pro-
gramming operation while an erase is suspended. In this case, data may be read from any
addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured
Silicon Sector area (One-time Program area), then user must use the proper command se-
quences to enter and exit this region.
Note that the Secured Silicon Sector autoselect, and
CFI functions are unavailable when program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Pro-
gram Suspend mode. The system can read as many autoselect codes as required. When the
device exits the autoselect mode, the device reverts to the Program Suspend mode, and is
ready for another valid operation. See
Autoselect Command Sequence on page 51
for more
information.
After the Program Resume command is written, the device reverts to programming. The sys-
tem can determine the status of the program operation using the DQ7 or DQ6 status bits, just
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See
Table 12 on page 63
and
Table 14 on
page 65
for program command sequence.
相關PDF資料
PDF描述
S29GL128N10FAI012 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAI013 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAI020 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAI022 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL128N10FAI023 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
相關代理商/技術參數
參數描述
S29GL128N10FFI010 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 128Mbit 16M/8M x 8bit/16bit 100ns 64-Pin Fortified BGA Tray 制造商:Spansion 功能描述:MIRRORBIT FLASH 128MB SMD 29LV128
S29GL128N10FFI020 制造商:Spansion 功能描述:Flash - NOR IC
S29GL128N10TF101 制造商:Spansion 功能描述:
S29GL128N10TFI010 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91
S29GL128N10TFI020 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*