- 您現在的位置：買賣IC網 > PDF目錄368096 > PPC440EPx-NpAfffTs (Applied Micro Circuits Corp.) PowerPC 440EPx Embedded Processor PDF資料下載
參數資料
| 型號： | PPC440EPx-NpAfffTs |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | PowerPC 440EPx Embedded Processor |
| 中文描述： | 嵌入式處理器的PowerPC 440EPx |
| 文件頁數： | 86/94頁 |
| 文件大?。?/td> | 738K |
| 代理商： | PPC440EPX-NPAFFFTS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
440EPx – PPC440EPx Embedded Processor
Preliminary Data Sheet
86
AMCC Proprietary
Revision 1.26 – October 15, 2007
insertion buffer.
When using unbuffered DIMMS, the loading on the address bus will be considerably greater than the clock (up to
18 loads for double-sided DIMMs). In this case, it is strongly suggested that a delay of 500 ps in the clock path so
that the Address/Command setup time at the DIMMs can be met. This delay is sufficient to meet the setup time,
without having to change the programmable delay (internal to the PPC440EPx) between the DQS/DQ/DM and the
clock (assuming nominal settings as specified in the PPC440EPx Users Manual). While the clock is now 500 ps
later than the nominal DQS arrival time, this still falls well within the window allowed by the JEDEC spec for T
DQSS
(± 0.25 cycle, or 1.5 ns at 166 MHz). In the case where it is not possible to anticipate which kind of DIMMs may be
employed in a system, it is always safe to use this 500 ps clock delay, since registered DIMMs (the least heavily
loaded) will have more than enough margin (almost 1/2 cycle) to accommodate the slight decrease in address hold
time.
Termination Model
Figure 10. DDR SDRAM Simulation Signal Termination Model
10pF
10pF
MemClkOut
MemClkOut
120
Ω
50
Ω
30pF
Addr/Ctrl/Data/DQS/DM (DDR1)
V
TT
= SOV
DD
/2
PPC440EPx
Addr/Ctrl (DDR2)
Note:
This diagram illustrates the model of the DDR SDRAM interface used when generating simulation timing data.
It is
not
a recommended physical circuit design for this interface. An actual interface design will depend on many
factors, including the type of memory used and the board layout.
DDR2 SDRAM On-Die Termination Impedance Setting
For all DDR2 applications, the On-Die Termination (ODT) impedance value
must
be set to 75 ohms in the DIMM
Extended Mode Register (EMR) in order to optimize the data transmission during memory write operations.
相關PDF資料 |
PDF描述 |
|---|---|
| PPC440EPx-SpAfffTs | PowerPC 440EPx Embedded Processor |
| PPC440EP | Power PC 440EP Embedded Processor |
| PPC440EP-3pbfffCx | Power PC 440EP Embedded Processor |
| PPC440GP-3CC333C | Power PC 440GP Embedded Processor |
| PPC440GP-3CC400C | Power PC 440GP Embedded Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PPC440EPX-NTA400E | 制造商:AMCC 功能描述:32 BIT POWERPC CORE, UP TO 667 MHZ, 2 10/100/1000 ETHERNET, - Trays |
| PPC440EPX-NTA400EZ | 制造商:AMCC 功能描述:32 BIT POWERPC CORE, UP TO 667 MHZ, 2 10/100/1000 ETHERNET, - Tape and Reel |
| PPC440EPX-NTA533E | 制造商:AMCC 功能描述:32 BIT POWERPC CORE, UP TO 667 MHZ, 2 10/100/1000 ETHERNET, - Trays |
| PPC440EPX-NTA533EZ | 制造商:AMCC 功能描述:32 BIT POWERPC CORE, UP TO 667 MHZ, 2 10/100/1000 ETHERNET, - Tape and Reel |
| PPC440EPX-NTA667E | 制造商:AMCC 功能描述:32 BIT POWERPC CORE, UP TO 667 MHZ, 2 10/100/1000 ETHERNET, - Trays |
發布緊急采購，3分鐘左右您將得到回復。