參數資料
型號： PIC18LF96J65-I/PT
廠商： Microchip Technology
文件頁數： 81/131頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 48KX16 100TQFP
標準包裝： 90
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 41.667MHz
連通性： EBI/EMI，以太網，I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 70
程序存儲器容量： 96KB（48K x 16）
程序存儲器類型： 閃存
RAM 容量： 3808 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 3.6 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TQFP
包裝： 托盤
2011 Microchip Technology Inc.
DS39762F-page 53
PIC18F97J60 FAMILY
3.7.1
OSCILLATOR CONTROL REGISTER
The OSCCON register (Register 3-2) controls several
aspects of the device clock’s operation, both in
full-power operation and in power-managed modes.
The System Clock Select bits, SCS<1:0>, select the
clock source. The available clock sources are the
primary clock (defined by the FOSC<2:0> Configura-
tion bits), the secondary clock (Timer1 oscillator) and
the internal oscillator. The clock source changes after
one or more of the bits are changed, following a brief
clock transition interval.
The OSTS (OSCCON<3>) and T1RUN (T1CON<6>)
bits indicate which clock source is currently providing
the device clock. The T1RUN bit indicates when the
Timer1 oscillator is providing the device clock in
secondary clock modes. In power-managed modes,
only one of these bits will be set at any time. If neither
bit is set, the INTRC source is providing the clock, or
the internal oscillator has just started and is not yet
stable.
The IDLEN bit determines if the device goes into Sleep
mode or one of the Idle modes when the SLEEP
instruction is executed.
The use of the flag and control bits in the OSCCON
register is discussed in more detail in Section 4.0
Note 1:
The Timer1 oscillator must be enabled to
select the secondary clock source. The
Timer1 oscillator is enabled by setting the
T1OSCEN bit in the Timer1 Control reg-
ister (T1CON<3>). If the Timer1 oscillator
is not enabled, then any attempt to select
a secondary clock source will be ignored.
2:
It is recommended that the Timer1
oscillator be operating and stable before
executing the SLEEP instruction or a very
long delay may occur while the Timer1
oscillator starts.
REGISTER 3-2:
OSCCON: OSCILLATOR CONTROL REGISTER
R/W-0
U-0
R-q
U-0
R/W-0
IDLEN
—
—OSTS(1)
—SCS1
SCS0
bit 7
bit 0
Legend:
q = Value determined by configuration
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
IDLEN:
Idle Enable bit
1
= Device enters Idle mode on SLEEP instruction
0
= Device enters Sleep mode on SLEEP instruction
bit 6-4
Unimplemented:
Read as ‘0’
bit 3
OSTS:
Oscillator Status bit(1)
1
= Device is running from oscillator source defined when SCS<1:0> = 00
0
= Device is running from oscillator source defined when SCS<1:0> = 01, 10 or 11
bit 2
Unimplemented:
Read as ‘0’
bit 1-0
SCS<1:0>:
System Clock Select bits
11
= Internal oscillator
10
= Primary oscillator
01
= Timer1 oscillator
When FOSC2 = 1;
00
= Primary oscillator
When FOSC2 = 0;
00
= Internal oscillator
Note 1:
Reset value is ‘0’ when Two-Speed Start-up is enabled and ‘1’ if disabled.
相關PDF資料
PDF描述
PIC24F16KL401-I/P IC MCU 16BIT 16KB FLASH 20-PDIP
PIC24FJ128GA010-I/PF IC PIC MCU FLASH 128KB 100TQFP
PIC24FJ256GA110-I/PF IC PIC MCU FLASH 256K 100TQFP
PIC24FJ256GB110-I/PF IC PIC MCU FLASH 256K 100TQFP
PIC24FJ64GA004-E/ML IC PIC MCU FLASH 64K 44-QFN
相關代理商/技術參數
參數描述
PIC1-R68-JT 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-JTQ 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-JTW 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-KT 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
PIC1-R68-KTQ 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*