- 您現在的位置：買賣IC網 > PDF目錄1965 > PIC18LF96J65-I/PT (Microchip Technology)IC PIC MCU FLASH 48KX16 100TQFP PDF資料下載
參數資料
| 型號： | PIC18LF96J65-I/PT |
| 廠商： | Microchip Technology |
| 文件頁數： | 78/131頁 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 48KX16 100TQFP |
| 標準包裝： | 90 |
| 系列： | PIC® 18F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 41.667MHz |
| 連通性： | EBI/EMI，以太網，I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 70 |
| 程序存儲器容量： | 96KB（48K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 3808 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 3.6 V |
| 數據轉換器： | A/D 16x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
PIC18F97J60 FAMILY
DS39762F-page 50
2011 Microchip Technology Inc.
3.3
Crystal Oscillator/Ceramic
Resonators (HS Modes)
In HS or HSPLL Oscillator modes, a crystal is
connected to the OSC1 and OSC2 pins to establish
oscillation. Figure 3-2 shows the pin connections.
The oscillator design requires the use of a crystal that
is rated for parallel resonant operation.
FIGURE 3-2:
CRYSTAL OSCILLATOR
OPERATION (HS OR
HSPLL CONFIGURATION)
TABLE 3-1:
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
3.4
External Clock Input (EC Modes)
The EC and ECPLL Oscillator modes require an exter-
nal clock source to be connected to the OSC1 pin.
There is no oscillator start-up time required after a
Power-on Reset or after an exit from Sleep mode.
In the EC Oscillator mode, the oscillator frequency,
divided by 4, is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 3-3 shows the pin connections for the EC
Oscillator mode.
FIGURE 3-3:
EXTERNAL CLOCK
INPUT OPERATION
(EC CONFIGURATION)
An external clock source may also be connected to the
OSC1 pin in the HS mode, as shown in Figure 3-4. In
this configuration, the OSC2 pin is left open. Current
consumption in this configuration will be somewhat
higher than EC mode, as the internal oscillator’s
feedback circuitry will be enabled (in EC mode, the
feedback circuit is disabled).
FIGURE 3-4:
EXTERNAL CLOCK
INPUT OPERATION
(HS CONFIGURATION)
Note:
Use of a crystal rated for series resonant
operation may give a frequency out of the
crystal manufacturer’s specifications.
Osc Type
Crystal
Freq.
Typical Capacitor Values
Tested:
C1
C2
HS
25 MHz
33 pF
Capacitor values are for design guidance only.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
VDD and temperature range for the application. Refer
to the following application notes for oscillator specific
information:
AN588, “PIC Microcontroller Oscillator Design
Guide”
AN826, “Crystal Oscillator Basics and Crystal
Selection for rfPIC and PIC Devices”
AN849, “Basic PIC Oscillator Design”
AN943, “Practical PIC Oscillator Analysis and
Design”
AN949, “Making Your Oscillator Work”
See the notes following this table for additional
information.
Note 1:
See Table 3-1 for initial values of C1 and C2.
2:
A series resistor (RS) may be required for
crystals with a low drive specification.
3:
RF varies with the oscillator mode chosen.
C1(1)
C2(1)
XTAL
OSC2
OSC1
RF(3)
Sleep
To
Logic
PIC18FXXJ6X
RS(2)
Internal
Note 1:
Higher capacitance increases the stabil-
ity of the oscillator but also increases the
start-up time.
2:
Since each crystal has its own character-
istics, the user should consult the crystal
manufacturer for appropriate values of
external components.
3:
Rs may be required to avoid overdriving
crystals with low drive level specifications.
4:
Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
OSC1/CLKI
OSC2/CLKO
FOSC/4
Clock from
Ext. System
PIC18FXXJ6X
OSC1
OSC2
Open
Clock from
Ext. System
PIC18FXXJ6X
(HS Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| PIC24F16KL401-I/P | IC MCU 16BIT 16KB FLASH 20-PDIP |
| PIC24FJ128GA010-I/PF | IC PIC MCU FLASH 128KB 100TQFP |
| PIC24FJ256GA110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ256GB110-I/PF | IC PIC MCU FLASH 256K 100TQFP |
| PIC24FJ64GA004-E/ML | IC PIC MCU FLASH 64K 44-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC1-R68-JT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-JTW | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KT | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
| PIC1-R68-KTQ | 制造商:RCD 制造商全稱:RCD COMPONENTS INC. 功能描述:SURFACE MOUNT POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。