- 您現在的位置：買賣IC網 > PDF目錄367810 > PCA9698 (NXP Semiconductors N.V.) 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT PDF資料下載
參數資料
| 型號： | PCA9698 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT |
| 中文描述： | 40位調頻I2C總線先進的I / O復位，光電和INT端口 |
| 文件頁數： | 17/47頁 |
| 文件大?。?/td> | 214K |
| 代理商： | PCA9698 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
PCA9698_2
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 19 July 2006
17 of 47
Philips Semiconductors
PCA9698
40-bit Fm+ I
2
C-bus advanced I/O port with RESET, OE and INT
7.6 GPIO All Call
A ‘GPIO All Call’ command allows the programming of multiple advanced GPIOs with
different I
2
C-bus addresses at the same time. This allows to optimize code programming
when the master needs to send the same instruction to several devices. To respond to
such a command and sequence, the PCA9698 needs to have its IOAC bit (register 2Ah,
bit 3) set to 1. Devices that have this bit set to 0 do not participate in any ‘GPIO All Call’
sequence.
The ‘GPIO All Call’ command can be performed only for a write operation and cannot be
used in conjunction with a read operation.
Master initiates a command sequence with the START command, the ‘GPIO All Call’
command associated with a Write command: Start
1101 110 + Write
All the devices that are programmed to respond to this command will acknowledge
The master then sends the data and all the devices that are programmed to respond
acknowledge the byte(s)
The master ends the sequence by sending a STOP or Repeated START command.
If the master initiates a ‘GPIO All Call’ sequence with a Read command, none of the slave
devices acknowledge.
7.7 Output state change on ACK or STOP
State change of the I/Os programmed as outputs can be done either:
during the ACK phase every time an Output Port register is modified. The output state
is then updated one-by-one (at a bank level): OCH bit = 1 (register 2Ah, bit 1)
at a STOP command allowing all the outputs to change at the exact same moment:
OCH bit = 0 (register 2Ah, bit 1).
Change of the outputs at the STOP command allows synchronizing of all the programmed
banks in a single device, and also allows synchronizing outputs of more than one
PCA9698.
Example 1:
Only one PCA9698 is used on the I
2
C-bus and all the outputs need to change
at the same time.
OCH bit (Mode Selection Register, bit 1) must be equal to ‘0’.
The master accesses the device and programs the Output Port register(s) that has
(have) to be changed (up to 5 ports).
When done, the master must generate a STOP command.
At the STOP command, the PCA9698 will update the Output Port register(s) that has
(have) been programmed and change the output states all at the same time.
Example 2:
More than one PCA9698 is used on the I
2
C-bus and all the outputs need to
change at the same time.
OCH bit (Mode Selection Register, bit 1) must be equal to ‘0’ in all the devices.
The master device must access the devices one-by-one.
Access to each device must be separated by a Re-START command.
相關PDF資料 |
PDF描述 |
|---|---|
| PCADADIO-CS | PC(ISA)BUS I/O CARD |
| PCB80C552-4 | 8-BIT MICROCONTROLLER |
| PCB80C39 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C49 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C552 | Single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9698BS | 制造商:NXP Semiconductors 功能描述:IC IO EXPANDER 40BIT I2C 5 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN; Chip Configuration:40bit; Bus Frequency:1MHz; Interface Type:I2C, SMBus; Supply Voltage Min:2.3V; Supply Voltage Max:5.5V; Digital IC Case Style:HVQFN; No. of Pins:56; No. of I/O's:40; MSL:MSL 1 ;RoHS Compliant: Yes |
| PCA9698BS,118 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698BS,118-CUT TAPE | 制造商:NXP 功能描述:PCA9698 Series 40-Bit Fm I2C-Bus Advanced I/O Port w/ Reset - HVQFN 56 |
| PCA9698DGG | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698DGG,512 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。