- 您現在的位置：買賣IC網 > PDF目錄367810 > PCA9698 (NXP Semiconductors N.V.) 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT PDF資料下載
參數資料
| 型號： | PCA9698 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT |
| 中文描述： | 40位調頻I2C總線先進的I / O復位，光電和INT端口 |
| 文件頁數： | 15/47頁 |
| 文件大?。?/td> | 214K |
| 代理商： | PCA9698 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
PCA9698_2
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 19 July 2006
15 of 47
Philips Semiconductors
PCA9698
40-bit Fm+ I
2
C-bus advanced I/O port with RESET, OE and INT
If ALLBNK = 1XX0 1100:
All I/Os configured as outputs in Bank 2 and 3 will be programmed with 1s, overwriting
values programmed in the Output Port registers 2 and 3, while I/Os configured as
outputs in Bank 0, 1, and 4 are programmed with values in Output Port registers 0, 1,
and 4.
7.4.8
MODE - PCA9698 mode selection register
This register allows programming of the PCA9698 modes.
OEPOL bit controls the polarity of OE pin.
–
OEPOL = 0: OE pin is active LOW.
–
OEPOL = 1: OE pin is active HIGH (equivalent to OE pin).
OCH bit selects the I
2
C-bus event where the state of the I/Os configured as outputs
change.
–
OCH = 0: outputs change on STOP command.
–
OCH = 1: outputs change on ACK.
IOAC bit controls the ability of the device to respond to a ‘GPIO All Call’ command
(see
Section 7.6 “GPIO All Call”
for more information), allowing programming of more
than one device at the same time.
–
IOAC = 0: The device cannot respond to a ‘GPIO All Call’ command.
–
IOAC = 1: The device can respond to a ‘GPIO All Call’ command.
Remark:
The ‘GPIO ALL CALL command defined for the PCA9698 is different from
the I
2
C-bus protocol ‘General Call’ command.
SMBA bit controls the capability of the PCA9698 to respond to a SMBAlert command.
–
SMBA = 0: PCA9698 does not respond to an Alert Response Address.
–
SMBA = 1: PCA9698 responds to an Alert Response Address. Bits 5, 6 and 7 are
reserved and must be programmed with 0s.
Unused bits (bits 2, 5, 6 and 7) must be programmed with 0s for proper device
operation.
Table 11.
Bit
Symbol
Default
MODE - mode selection register (address 2Ah) description
7
6
5
X
X
X
0
0
0
4
3
2
X
0
1
0
SMBA
0
IOAC
0
OCH
1
OEPOL
0
相關PDF資料 |
PDF描述 |
|---|---|
| PCADADIO-CS | PC(ISA)BUS I/O CARD |
| PCB80C552-4 | 8-BIT MICROCONTROLLER |
| PCB80C39 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C49 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C552 | Single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9698BS | 制造商:NXP Semiconductors 功能描述:IC IO EXPANDER 40BIT I2C 5 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN; Chip Configuration:40bit; Bus Frequency:1MHz; Interface Type:I2C, SMBus; Supply Voltage Min:2.3V; Supply Voltage Max:5.5V; Digital IC Case Style:HVQFN; No. of Pins:56; No. of I/O's:40; MSL:MSL 1 ;RoHS Compliant: Yes |
| PCA9698BS,118 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698BS,118-CUT TAPE | 制造商:NXP 功能描述:PCA9698 Series 40-Bit Fm I2C-Bus Advanced I/O Port w/ Reset - HVQFN 56 |
| PCA9698DGG | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698DGG,512 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。