- 您現在的位置：買賣IC網 > PDF目錄367810 > PCA9698 (NXP Semiconductors N.V.) 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT PDF資料下載
參數資料
| 型號： | PCA9698 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 40-bit Fm+ I2C-bus advanced I/O port with RESET, OE and INT |
| 中文描述： | 40位調頻I2C總線先進的I / O復位，光電和INT端口 |
| 文件頁數： | 16/47頁 |
| 文件大?。?/td> | 214K |
| 代理商： | PCA9698 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
PCA9698_2
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 19 July 2006
16 of 47
Philips Semiconductors
PCA9698
40-bit Fm+ I
2
C-bus advanced I/O port with RESET, OE and INT
7.5 Device ID - PCA9698 ID field
The Device ID field is a 3 byte read-only (24 bits) word giving the following information:
12 bits with the manufacturer name, unique per manufacturer (e.g., Philips)
9 bits with the part identification, assigned by manufacturer (e.g., PCA9698)
3 bits with the die revision, assigned by manufacturer (e.g., RevX)
The Device ID is read-only, hard-wired in the device and can be accessed as follows:
1. START command
2. The master sends the Reserved Device ID I
2
C-bus address followed by the R/W bit
set to ‘0’ (write): ‘1111 1000’.
3. The master sends the I
2
C-bus slave address of the slave device it needs to identify.
The LSB is a ‘Don’t care’ value. Only one device must acknowledge this byte (the one
that has the I
2
C-bus slave address).
4. The master sends a Re-START command.
Remark:
A STOP command followed by a START command will reset the slave state
machine and the Device ID Read cannot be performed. Also, a STOP command or a
Re-START command followed by an access to another slave device will reset the
slave state machine and the Device ID Read cannot be performed.
5. The master sends the Reserved Device ID I
2
C-bus address followed by the R/W bit
set to ‘1’ (read): ‘1111 1001’.
6. The Device ID Read can be done, starting with the 12 manufacturer bits (first byte +
4 MSBs of the second byte), followed by the 9 part identification bits (4 LSBs of the
second byte + 5 MSBs of the third byte), and then the 3 die revision bits (3 LSBs of
the third byte).
7. The master ends the reading sequence by NACKing the last byte, thus resetting the
slave device state machine and allowing the master to send the STOP command.
Remark:
The reading of the Device ID can be stopped anytime by sending a NACK
command.
If the master continues to ACK the bytes after the third byte, the PCA9698 rolls back
to the first byte and keeps sending the Device ID sequence until a NACK has been
detected.
For the PCA9698, the Device ID is as shown in
Figure 10
.
Fig 10. PCA9698 ID field
0
002aab942
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
revision
0
0
0
0
0
part identification
manufacturer
相關PDF資料 |
PDF描述 |
|---|---|
| PCADADIO-CS | PC(ISA)BUS I/O CARD |
| PCB80C552-4 | 8-BIT MICROCONTROLLER |
| PCB80C39 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C49 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| PCB80C552 | Single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9698BS | 制造商:NXP Semiconductors 功能描述:IC IO EXPANDER 40BIT I2C 5 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN 制造商:NXP Semiconductors 功能描述:IC, IO EXPANDER, 40BIT, I2C, 56HVQFN; Chip Configuration:40bit; Bus Frequency:1MHz; Interface Type:I2C, SMBus; Supply Voltage Min:2.3V; Supply Voltage Max:5.5V; Digital IC Case Style:HVQFN; No. of Pins:56; No. of I/O's:40; MSL:MSL 1 ;RoHS Compliant: Yes |
| PCA9698BS,118 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698BS,118-CUT TAPE | 制造商:NXP 功能描述:PCA9698 Series 40-Bit Fm I2C-Bus Advanced I/O Port w/ Reset - HVQFN 56 |
| PCA9698DGG | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9698DGG,512 | 功能描述:接口-I/O擴展器 I2C I/O EXPANDER GP RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。