- 您現在的位置：買賣IC網 > PDF目錄363665 > NSAM265SRA (National Semiconductor Corporation) CompactSPEECH Digital Speech Processors PDF資料下載
參數資料
| 型號： | NSAM265SRA |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | CompactSPEECH Digital Speech Processors |
| 中文描述： | CompactSPEECH數字語音處理器 |
| 文件頁數： | 13/58頁 |
| 文件大小： | 712K |
| 代理商： | NSAM265SRA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
2.0 Functional Description
(Continued)
The MWRDY signal is used as follows:
1. An active (0) MWRDY signal signals the microcontroller
that the last eight bits of data transferred to/from the
CompactSPEECH were accepted and processed (see
below).
2. The MWRDY signal is deactivated (set to 1 by the Com-
pactSPEECH) after 8 bits of data were transferred to/
from the CompactSPEECH. The bit is set following the
falling edge of the eighth MWCLK clock-cycle.
3. The MWRDY signal is activated (by the Compact-
SPEECH) when the CompactSPEECH is ready to receive
the first parameter byte (if there are any parameters) and
so on till the last byte of parameters is transferred. An
active MWRDY signal after the last byte of parameters
indicates that the command was parsed and (if possible)
executed. If that command has a return value, the micro-
controller must read the value before issuing a new com-
mand.
4. When a return value is transmitted, the MWRDY signal is
deactivated after every byte and activated again when
the CompactSPEECH is ready to send another byte, or to
receive a new command.
The MWRDY signal is activated (set to 0) after reset and
protocol timeout. (See Section 2.3.3.)
The MWRQST signal is used as follows:
1. The MWRQST signal is activated (0), when the status
word is changed.
2. The MWRQST signal remains active (0), until the Com-
pactSPEECH receives a GSW command.
Figure 2-2 illustrates the sequence of activities during a
MICROWIRE data transfer.
2.3.3 Interface Protocol Error Handling
Interface Protocol Time-Outs
When the time between two consecutive byte transmis-
sions, or bytes reception within the same command or re-
turn value, exceeds two milliseconds after the MWRDY sig-
nal is asserted, a time-out event occurs, and the Compact-
SPEECH responds as follows:
1. Sets the error bit in the status word to 1.
2. Sets the EVDTIMEOUT bit in the error word to 1.
3. Activates the MWRQST signal (sets it to 0).
4. Activates the MWRDY signal (sets it to 0).
5. Waits for a new command. (After a time-out occurs, the
microcontroller must wait at least four milliseconds before
issuing the next command.)
Echo Mechanism
The CompactSPEECH echoes back to the microcontroller
all the bits received by the CompactSPEECH. Upon detec-
tion of an error in the echo the microcontroller should stop
the protocol clock, which eventually will cause a time-out
error (i.e., ERRDTIMEOUT bit is set in the error word).
Note:
When a command has a return value, the CompactSPEECH transmits
bytes of the return value instead of the echo value.
When the CompactSPEECH is transmitting a byte, it ex-
pects to receive the value 0xAA as an echo. Upon detection
of an error the CompactSPEECH activates the MWRQST
signal, and sets the ERRDCOMM bit in the error word.
2.4 CODEC INTERFACE
The CompactSPEECH provides an on-chip interface to a
serial codec. The interface supports codec operation in long
or short-frame formats. The format is selected with the CFG
command.
The codec interface uses four signalsDCDIN, CDOUT,
CCLK and CFS0.
Data is transferred to the codec through the CDOUT pin.
Data is read from the codec through the CDIN pin.
Data transfer between the CompactSPEECH and the serial
codec starts by the CompactSPEECH asserting (high) the
CFS0 frame sync signal. After one clock cycle, the Com-
pactSPEECH de-asserts CFS0, data from the Compact-
SPEECH is sent to the codec through CDOUT, and simulta-
neously data from the codec is sent to the Compact-
SPEECH through CDIN.
TL/EE/12378–5
FIGURE 2-2. Sequence of Activities During a MICROWIRE Byte Transfer
13
相關PDF資料 |
PDF描述 |
|---|---|
| NSAM266SVLJ | 4 Mbit Uniform Sector, Serial Flash Memory |
| NSAM266SA | 4 Mbit Uniform Sector, Serial Flash Memory |
| NSAM266SAA | 4 Mbit Uniform Sector, Serial Flash Memory |
| NSB8 | BASIC interpreter for Z80 family |
| NSB9435T1 | High Current Bias Resistor Transistors(高強度電流偏置電阻晶體管) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NSAM265SRAV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| NSAM265SRAVLJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| NSAM266SA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:NSAM266SA CompactSPEECHTM Digital Speech Processor with Serial Flash Interface |
| NSAM266SAA | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:NSAM266SA CompactSPEECHTM Digital Speech Processor with Serial Flash Interface |
| NSAM266SAA/V | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:NSAM266SA CompactSPEECHTM Digital Speech Processor with Serial Flash Interface |
發布緊急采購，3分鐘左右您將得到回復。