- 您現在的位置：買賣IC網 > PDF目錄224596 > NAND01GR4B2BZA1F (STMICROELECTRONICS) 64M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 PDF資料下載
參數資料
| 型號： | NAND01GR4B2BZA1F |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 64M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 |
| 封裝： | 9 X 11 MM, 1 MM HEIGHT, 0.80 MM PITCH, LEAD FREE, VFBGA-63 |
| 文件頁數： | 25/63頁 |
| 文件大?。?/td> | 684K |
| 代理商： | NAND01GR4B2BZA1F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
NAND01G-B2B, NAND02G-B2C
Device operations
31/63
6.6
Block Erase
Erase operations are done one block at a time. An erase operation sets all of the bits in the
addressed block to ‘1’. All previous data in the block is lost.
An erase operation consists of three steps (refer to Figure 14):
1.
One bus cycle is required to setup the Block Erase command. Only addresses A18-
A28 (x8) or A17-A27 (x16) are used, the other address inputs are ignored.
2.
two or three bus cycles are then required to load the address of the block to be erased.
3.
one bus cycle is required to issue the Block Erase confirm command to start the P/E/R
Controller.
The operation is initiated on the rising edge of write Enable, W, after the confirm command
is issued. The P/E/R Controller handles Block Erase and implements the verify process.
During the Block Erase operation, only the Read Status Register and Reset commands will
be accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High. If the operation completed successfully, the Write Status Bit
SR0 is ‘0’, otherwise it is set to ‘1’.
Figure 14.
Block Erase Operation
6.7
Reset
The Reset command is used to reset the Command Interface and Status Register. If the
Reset command is issued during any operation, the operation will be aborted. If it was a
program or erase operation that was aborted, the contents of the memory locations being
modified will no longer be valid as the data will be partially programmed or erased.
If the device has already been reset then the new Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after the Reset command is issued. The value
of tBLBH4 depends on the operation that the device was performing when the command was
issued, refer to Table 25: AC Characteristics for Operations for the values.
I/O
RB
Block Address
Inputs
SR0
ai07593
D0h
70h
60h
Block Erase
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH3
(Erase Busy time)
相關PDF資料 |
PDF描述 |
|---|---|
| NAND08GR4B3AZB6 | 512M X 16 FLASH 1.8V PROM, 25000 ns, PBGA63 |
| NAND256W4A2AZA6E | 16M X 16 FLASH 3V PROM, 12000 ns, PBGA55 |
| NCP303LSN41T1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| NCS6416DWG | 8-CHANNEL, VIDEO MULTIPLEXER, PDSO20 |
| NCS6S4803L5C | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NAND01GR4B2BZA6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GR4B2BZA6E | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory |
| NAND01GR4B2BZA6F | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1-Gbit, 2-Gbit, 2112-byte/1056-word page, 1.8 V/3 V, NAND flash memory |
| NAND01GR4B2BZB1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
| NAND01GR4B2BZB6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Gbit, 2 Gbit, 2112 Byte/1056 Word Page, 1.8V/3V, NAND Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。