- 您現在的位置：買賣IC網 > PDF目錄299522 > MT46H32M32LGCM-5IT:A 32M X 32 DDR DRAM, 5 ns, PBGA90 PDF資料下載
參數資料
| 型號： | MT46H32M32LGCM-5IT:A |
| 元件分類： | DRAM |
| 英文描述： | 32M X 32 DDR DRAM, 5 ns, PBGA90 |
| 封裝： | 10 X 13 MM, GREEN, PLASTIC, VFBGA-90 |
| 文件頁數： | 15/95頁 |
| 文件大?。?/td> | 3231K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
Table 9: IDD6 Specifications and Conditions
Notes 1–5, 7, and 12 apply to all the parameters/conditions in this table; VDD/VDDQ = 1.70–1.95V
Parameter/Condition
Symbol Low Power
Standard
Units
Self refresh:
CKE = LOW; tCK = tCK (MIN); Address and control
inputs are stable; Data bus inputs are stable
Full array, 85C
IDD6
1000
1200
μA
Full array, 45C
500
750
μA
1/2 array, 85C
750
900
μA
1/2 array, 45C
440
730
μA
1/4 array, 85C
600
750
μA
1/4 array, 45C
380
680
μA
1/8 array, 85C
550
750
μA
1/8 array, 45C
350
620
μA
1/16 array, 85C
500
700
μA
1/16 array, 45C
330
540
μA
Notes: 1. All voltages referenced to VSS.
2. Tests for IDD characteristics may be conducted at nominal supply voltage levels, but the
related specifications and device operation are guaranteed for the full voltage range
specified.
3. Timing and IDD tests may use a VIL-to-VIH swing of up to 1.5V in the test environment,
but input timing is still referenced to VDDQ/2 (or to the crossing point for CK/CK#). The
output timing reference voltage level is VDDQ/2.
4. IDD is dependent on output loading and cycle rates. Specified values are obtained with
minimum cycle time with the outputs open.
5. IDD specifications are tested after the device is properly initialized and values are aver-
aged at the defined cycle rate.
6. MIN (tRC or tRFC) for IDD measurements is the smallest multiple of tCK that meets the
minimum absolute value for the respective parameter. tRAS (MAX) for IDD measure-
ments is the largest multiple of tCK that meets the maximum absolute value for tRAS.
7. Measurement is taken 500ms after entering into this operating mode to provide settling
time for the tester.
8. VDD must not vary more than 4% if CKE is not active while any bank is active.
9. IDD2N specifies DQ, DQS, and DM to be driven to a valid high or low logic level.
10. CKE must be active (HIGH) during the entire time a REFRESH command is executed.
From the time the AUTO REFRESH command is registered, CKE must be active at each
rising clock edge until tRFC later.
11. This limit is a nominal value and does not result in a fail. CKE is HIGH during REFRESH
command period (tRFC [MIN]) else CKE is LOW (for example, during standby).
12. Values for IDD6 85C are guaranteed for the entire temperature range. All other IDD6 val-
ues are estimated.
13. Typical values at 25C, not a maximum value.
1Gb: x16, x32 Mobile LPDDR SDRAM
Electrical Specifications – IDD Parameters
PDF: 09005aef82ce3074
1gb_ddr_mobile_sdram_t48m.pdf - Rev. K 07/09 EN
22
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2007 Micron Technology, Inc. All rights reserved.
相關PDF資料 |
PDF描述 |
|---|---|
| MT46HC32M16LFCX-75:B | 32M X 16 DDR DRAM, 7.5 ns, PBGA90 |
| MT46HC32M16LGCM-54IT:B | 32M X 16 DDR DRAM, 5.4 ns, PBGA90 |
| MT47H32M16BT-37VL:A | 32M X 16 DDR DRAM, 0.5 ns, PBGA92 |
| MT47H64M16HQ-3IT:G | 64M X 16 DDR DRAM, 0.4 ns, PBGA60 |
| MT47H64M8CF-5EAT:F | DDR DRAM, PBGA60 |
相關代理商/技術參數 |
參數描述 |
|---|
發布緊急采購，3分鐘左右您將得到回復。