參數資料
型號： MSP34X1G
廠商： Electronic Theatre Controls, Inc.
英文描述： Multistandard Sound Processor Family with Virtual Dolby Surround
中文描述： 多標準聲音處理器系列與虛擬杜比環繞聲
文件頁數： 24/104頁
文件大?。?/td> 871K
代理商： MSP34X1G
MSP 34x1G
PRELIMINARY DATA SHEET
24
Micronas
3.3.2.1. STANDARD SELECT Register
The TV sound standard of the MSP 34x1G demodula-
tor is determined by the STANDARD SELECT register.
There are two ways to use the STANDARD SELECT
register:
–
Setting up the demodulator for a TV sound standard
by sending the corresponding standard code with a
single I
2
C bus transmission.
–
Starting the Automatic Standard Detection
for ter-
restrial TV standards.
This is the most comfortable
way to set up the demodulator. Within 0.5 s, the
detection and setup of the actual TV sound standard
is performed. The detected standard can be read
out of the STANDARD RESULT register by the con-
trol processor. This feature is recommended for the
primary setup of a TV set. Outputs should be muted
during Automatic Standard Detection.
The Standard Codes are listed in Table 3
–
7.
Selecting a TV sound standard via the STANDARD
SELECT register initializes the demodulator. This
includes: AGC-settings and carrier mute, tuning fre-
quencies, FIR-filter settings, demodulation mode (FM,
AM, NICAM), deemphasis and identification mode.
TV stereo sound standards that are unavailable for a
specific MSP version are processed in analog mono
sound of the standard. In that case, stereo or bilingual
processing will not be possible.
For a complete setup of the TV sound processing from
analog IF input to the source selection, the transmis-
sions as shown in Section 3.5. are necessary.
For reasons of software compatibility to the
MSP 34xxD, a Manual/Compatibility mode is available.
A detailed description of this mode can be found on
page 85.
3.3.2.2. Refresh of STANDARD SELECT Register
A general refresh of the STANDARD SELECT register
is not allowed. However, the following method
enables watching the MSP 34x1G
“
alive
”
status and
detection of accidental resets (only versions B6 and
later):
–
After Power-on, bit[15] of CONTROL will be set; it
must be read once to enable the reset-detection
feature.
–
Reading of the CONTROL register and checking
the reset indicator bit[15] .
–
If bit[15] is
“
0
”
, any refresh of the STANDARD
SELECT register
is not allowed.
–
If bit[15] is
“
1
”
, indicating a reset, a refresh of the
STANDARD SELECT register and all other MSPG
registers is required.
3.3.2.3. STANDARD RESULT Register
If Automatic Standard Detection is selected in the
STANDARD SELECT register, status and result of the
Automatic Standard Detection process can be read out
of the STANDARD RESULT register. The possible
results are based on the mentioned Standard Code
and are listed in Table 3
–
8.
In cases where no sound standard has been detected
(no standard present, too much noise, strong interfer-
ers, etc.) the STANDARD RESULT register contains
00 00
hex
. In that case, the controller has to start further
actions (for example set the standard according to a
preference list or by manual input).
As long as the STANDARD RESULT register contains
a value greater than 07 FF
hex
, the Automatic Standard
Detection is still active. During this period, the MODUS
and STANDARD SELECT register must not be written.
The STATUS register will be updated when the Auto-
matic Standard Detection has finished.
If a present sound standard is unavailable for a spe-
cific MSP-version, it detects and switches to the ana-
log mono sound of this standard.
Example:
The MSPs 3421G and 3441G will detect a B/G-NICAM
signal as standard 3 and will switch to the analog FM-
Mono sound.
相關PDF資料
PDF描述
MSP600-3-K-5-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-K-5-N-4 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-3-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-3-N-4 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-4-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
相關代理商/技術參數
參數描述
MSP34X2G 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Multistandard Sound Processor Family with Dolby Surround Pro Logic
MSP34X5G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MSP 34x5G Multistandard Sound Processor Family
MSP34X7G 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Multistandard Sound Processor Family
MSP3B10000FS14E3 功能描述:線繞電阻器 - SMD MSP 3 B 1K 1% BA100 e3 RoHS:否 制造商:Ohmite 電阻:4.99 Ohms 容差:1 % 功率額定值:2 W 外殼代碼 - in:4023 外殼代碼 - mm:10357 溫度系數:50 PPM / C 系列:RW2 工作溫度范圍:- 55 C to + 125 C 封裝:Bulk
MSP3B10000JS14E3 功能描述:線繞電阻器 - SMD MSP 3 B 1K 5% BA100 e3 RoHS:否 制造商:Ohmite 電阻:4.99 Ohms 容差:1 % 功率額定值:2 W 外殼代碼 - in:4023 外殼代碼 - mm:10357 溫度系數:50 PPM / C 系列:RW2 工作溫度范圍:- 55 C to + 125 C 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*