參數資料
型號： MSP34X1G
廠商： Electronic Theatre Controls, Inc.
英文描述： Multistandard Sound Processor Family with Virtual Dolby Surround
中文描述： 多標準聲音處理器系列與虛擬杜比環繞聲
文件頁數： 11/104頁
文件大?。?/td> 871K
代理商： MSP34X1G
PRELIMINARY DATA SHEET
MSP 34x1G
Micronas
11
2.2.3. Preprocessing of Demodulator Signals
The NICAM signals must be processed by a deempha-
sis filter and adjusted in level. The analog demodu-
lated signals must be processed by a deemphasis fil-
ter, adjusted in level, and dematrixed. The correct
deemphasis filters are already selected by setting the
standard in the STANDARD SELECT register. The
level adjustment has to be done by means of the FM/
AM and NICAM prescale registers. The necessary
dematrix function depends on the selected sound stan-
dard and the actual broadcasted sound mode (mono,
stereo, or bilingual). It can be manually set by the FM
Matrix Mode register or automatically by the Automatic
Sound Selection.
2.2.4. Automatic Sound Select
In the Automatic Sound Select mode, the dematrix
function is automatically selected based on the identifi-
cation information in the STATUS register. No I
2
C
interaction is necessary when the broadcasted sound
mode changes (e.g. from mono to stereo).
The demodulator supports the identification check by
switching between mono-compatible standards (stan-
dards that have the same FM-Mono carrier) automati-
cally and non-audible. If B/G-FM or B/G-NICAM is
selected, the MSP will switch between these stan-
dards. The same action is performed for the stan-
dards: D/K1-FM, D/K2-FM, D/K3-FM and D/K-NICAM.
Switching is only done in the absence of any stereo or
bilingual identification. If identification is found, the
MSP keeps the detected standard.
In case of high bit-error rates, the MSP 34x1G auto-
matically falls back from digital NICAM sound to ana-
log FM or AM mono.
Table 2
–
1 summarizes all actions that take place when
Automatic Sound Select is switched on.
To provide more flexibility, the Automatic Sound Select
block prepares four different source channels of
demodulated sound (Fig. 2
–
2). By choosing one of the
four demodulator channels, the preferred sound mode
can be selected for each of the output channels (loud-
speaker, headphone, etc.). This is done by means of
the Source Select registers.
The following source channels of demodulated sound
are defined:
–
“
FM/AM
”
channel:
Analog mono sound, stereo if
available. In case of NICAM, analog mono only
(FM or AM mono).
–
“
Stereo or A/B
”
channel:
Analog or digital mono
sound, stereo if available. In case of bilingual broad-
cast, it contains both languages A (left) and B
(right).
–
“
Stereo or A
”
channel:
Analog or digital mono
sound, stereo if available. In case of bilingual broad-
cast, it contains language A (on left and right).
–
“
Stereo or B
”
channel:
Analog or digital mono
sound, stereo if available. In case of bilingual broad-
cast, it contains language B (on left and right).
Fig. 2
–
2 and Table 2
–
2 show the source channel
assignment of the demodulated signals in case of
Automatic Sound Select mode for all sound standards.
Note:
The analog primary input channel contains the
signal of the mono FM/AM carrier or the L+R signal of
the MPX carrier. The secondary input channel contains
the signal of the 2nd FM carrier, the L-R signal of the
MPX carrier, or the SAP signal.
Fig. 2
–
2:
Source channel assignment of demodulated
signals in Automatic Sound Select Mode
2.2.5. Manual Mode
Fig. 2
–
3 shows the source channel assignment of
demodulated signals in case of manual mode. If man-
ual mode is required, more information can be found in
Section 6.7.
“
Demodulator Source Channels in Manual
Mode
”
on page 99.
Fig. 2
–
3:
Source channel assignment of demodulated
signals in Manual Mode
2.3. Preprocessing for SCART and
I
2
S Input Signals
The SCART and I
2
S inputs need only be adjusted in
level by means of the SCART and I
2
S prescale regis-
ters.
S
FM/AM
Stereo or A/B
Stereo or A
Stereo or B
0
1
3
4
primary
channel
FM/AM
Prescale
NICAM
Prescale
Automatic
Sound
Select
secondary
channel
NICAM A
NICAM B
LS Ch.
Matrix
Output-Ch.
matrices
must be set
once to
stereo.
S
FM/AM
(Stereo or A/B)
0
1
primary
channel
FM/AM
Prescale
NICAM
Prescale
FM-Matrix
secondary
channel
NICAM A
NICAM B
LS Ch.
Matrix
Output-Ch.
matrices
must be set
according to
the standard.
NICAM
相關PDF資料
PDF描述
MSP600-3-K-5-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-K-5-N-4 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-3-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-3-N-4 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
MSP600-3-P-4-N-1 NEW HIGH ACCURACY, DIGITALLY COMPENSATED EMI/RFI PROTECTED STAINLESS STEEL ISOLATED PRESSURE TRANSDUCER
相關代理商/技術參數
參數描述
MSP34X2G 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Multistandard Sound Processor Family with Dolby Surround Pro Logic
MSP34X5G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MSP 34x5G Multistandard Sound Processor Family
MSP34X7G 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Multistandard Sound Processor Family
MSP3B10000FS14E3 功能描述:線繞電阻器 - SMD MSP 3 B 1K 1% BA100 e3 RoHS:否 制造商:Ohmite 電阻:4.99 Ohms 容差:1 % 功率額定值:2 W 外殼代碼 - in:4023 外殼代碼 - mm:10357 溫度系數:50 PPM / C 系列:RW2 工作溫度范圍:- 55 C to + 125 C 封裝:Bulk
MSP3B10000JS14E3 功能描述:線繞電阻器 - SMD MSP 3 B 1K 5% BA100 e3 RoHS:否 制造商:Ohmite 電阻:4.99 Ohms 容差:1 % 功率額定值:2 W 外殼代碼 - in:4023 外殼代碼 - mm:10357 溫度系數:50 PPM / C 系列:RW2 工作溫度范圍:- 55 C to + 125 C 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*