參數資料
型號： MC68L11F1CFN3
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, EEPROM, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 79/174頁
文件大?。?/td> 981K
代理商： MC68L11F1CFN3
MC68HC11F1
PIN DESCRIPTIONS
MOTOROLA
TECHNICAL DATA
2-3
2.2 Reset (RESET)
An active low bidirectional control signal, RESET, acts as an input to initialize the MCU
to a known start-up state. It also acts as an open-drain output to indicate that an inter-
nal failure has been detected in either the clock monitor or COP watchdog circuit. The
CPU distinguishes between internal and external reset conditions by sensing whether
the reset pin rises to a logic one in less than two E-clock cycles after a reset has oc-
curred. It is not advisable to connect an external resistor-capacitor (RC) power-up de-
lay circuit to the reset pin of M68HC11 devices because the circuit charge time
constant can cause the device to misinterpret the type of reset that occurred. Refer to
SECTION 5 RESETS AND INTERRUPTS for further information.
Figure 2-3 illustrates a reset circuit that uses an external switch. Other circuits can be
used, however, it is important to incorporate a low voltage interrupt (LVI) circuit to pre-
vent operation at insufficient voltage levels which could result in erratic behavior or cor-
ruption of RAM.
Figure 2-3 External Reset Circuit
2.3 E-Clock Output (E)
E is the output connection for the internally generated E clock. The signal from E is
used as a timing reference. The frequency of the E-clock output is one fourth that of
the input frequency at the EXTAL pin. When E-clock output is low, an internal process
is taking place. When it is high, data is being accessed. All clocks, including the E
clock, are halted when the MCU is in STOP mode. The E clock can be turned off in
single-chip modes to reduce the effects of radio frequency interference (RFI). Refer to
2.4 Crystal Driver and External Clock Input (XTAL, EXTAL)
These two pins provide the interface for either a crystal or a CMOS-compatible clock
to control the internal clock generator circuitry. Either a crystal oscillator or a CMOS
compatible clock can be used. The resulting E-clock rate is the input frequency divided
by four.
MANUAL
RESET SWITCH
4.7 k
TO RESET
OF M68HC11
4.7 k
VDD
MC34064
IN
GND
2
3
1
RESET
1.0
F
4.7 k
VDD
MC34164
IN
GND
2
3
1
RESET
OPTIONAL POWER-ON DELAY
AND MANUAL RESET SWITCH
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*