參數資料
型號： MC68L11F1CFN3
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, EEPROM, MICROCONTROLLER, PQCC68
封裝： PLASTIC, LCC-68
文件頁數： 174/174頁
文件大?。?/td> 981K
代理商： MC68L11F1CFN3
MC68HC11F1
SERIAL PERIPHERAL INTERFACE
MOTOROLA
TECHNICAL DATA
8-1
SECTION 8 SERIAL PERIPHERAL INTERFACE
The serial peripheral interface (SPI), an independent serial communications sub-
system, allows the MCU to communicate synchronously with peripheral devices, such
as transistor-transistor logic (TTL) shift registers, liquid crystal display (LCD) drivers,
analog-to-digital converter subsystems, and other microprocessors. The SPI is also
capable of inter-processor communication in a multiple master system. The SPI sys-
tem can be configured as either a master or a slave device. When configured as a
master, data transfer rates can be as high as one-half the E-clock rate (2.5 Mbits per
second for a 5-MHz bus frequency). When configured as a slave, data transfers can
be as fast as the E-clock rate (5 Mbits per second for a 5-MHz bus frequency).
8.1 Functional Description
The central element in the SPI system is the block containing the shift register and the
read data buffer. The system is single buffered in the transmit direction and double
buffered in the receive direction. This means that new data for transmission cannot be
written to the shifter until the previous transfer is complete; however, received data is
transferred into a parallel read data buffer so the shifter is free to accept a second se-
rial character. As long as the first character is read out of the read data buffer before
the next serial character is ready to be transferred, no overrun condition occurs. A sin-
gle MCU register address is used for reading data from the read data buffer and for
writing data to the shifter.
The SPI status block represents the SPI status flags (transfer complete, write collision,
and mode fault) located in the SPI status register (SPSR). The SPI control block rep-
resents those functions that control the SPI system through the serial peripheral con-
trol register (SPCR).
Refer to Figure 8-1, which shows the SPI block diagram.
相關PDF資料
PDF描述
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68HC11F1CFN3R2 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC68
MC68SZ328VH66V 66 MHz, RISC PROCESSOR, PBGA196
MC74F2970N DRAM CONTROLLER, PDIP24
MC908GP32CFBR2 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
MC68L11F1CFNE3 功能描述:8位微控制器 -MCU 8B MCU 1KRAM 512BYTES RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L11K1FN2R2 制造商:Motorola Inc 功能描述:
MC68L11K1FUE2 功能描述:8位微控制器 -MCU 8B MCU L-VOLTAGE-EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68L711E9FN2 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68L711E9FNE2 功能描述:8位微控制器 -MCU 8B MCU LO VOLTAGE RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*