參數資料
型號: MC68HC711G5CFN
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84
封裝: PLASTIC, LCC-84
文件頁數: 17/195頁
文件大小: 1940K
代理商: MC68HC711G5CFN
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁
ANALOG-TO-DIGITAL CONVERTER
9-1
SECTION 9
ANALOG-TO-DIGITAL CONVERTER
The Analog to Digital converter system consists of a single 10-bit successive approximation type
converter and a 16-channel multiplexer. Eight of the channels are connected to pins on the
MC68HC11G5, four are unused and the remaining four channels are dedicated to internal reference
points or test functions. There are eight 10-bit result registers and control logic allows for four or eight
consecutive conversions before stopping or for conversions to continue with the newest conversion
overwriting the oldest result register. Also, the control logic allows conversions to be performed on
a single selected channel, multiple times or consecutively on a selected group of four channels. In
addition, the control logic allows for converting all eight channels and either stopping or converting
continuously.
Two dedicated lines (Vrl and Vrh) are provided for the reference voltage inputs. These pins may be
connected to a separate or isolated power supply to ensure full accuracy of the AD conversion.
The 10-bit A/D converter accepts analog inputs ranging from Vrl to Vrh. Smaller input ranges can
also be obtained by adjusting Vrl and Vrh to the desired upper and lower limits. Conversion is
specified and tested for Vrl = 0 volts and Vrh = 5 volts. The A/D system can be operated with Vrh below
VDD and/or Vrl above VSS as long as Vrh is above Vrl by enough to support the conversions (2.5
to 5.0 volts).
Each set of four conversions takes 144 cycles of the E-clock, provided that E is greater than or equal
to 750 kHz. If E is less than 750 kHz, an internal R-C oscillator, which is nominally 1.5 MHz, must
be used for the A/D conversion clock. When the internal R-C oscillator is being used as the
conversion clock, the conversion complete flag (CCF) must be used to determine when a conversion
sequence has been completed. When using the internal R-C oscillator for A/D conversions the
sample and conversion process runs at the nominal 1.5 MHz rate; however, the conversion results
must be transferred to the MCU result registers synchronously with the MCU E-clock, so conversion
time is limited to a maximum of one channel per E-clock cycle.
Two control bits in the OPTION register control the basic configuration of the A/D system. The A to D
power-up bit (ADPU) allows the system to be disabled, resulting in reduced power consumption
when the A/D system is not being used. Any conversion which is in process when ADPU is written
to zero will be aborted. A delay of typically 100 microseconds is required after turning on the A/D
(by writing ADPU from 0 to 1) for the analog and comparator sections to stabilize. The CSEL bit is
used to select either the internal R-C oscillator or the MCU E-clock as the A/D system clock source.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC11G7CFN 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84
MC68HC711L6CFN1 OTPROM, MICROCONTROLLER, PQCC68
MC68HC805C4CP 8-BIT, EEPROM, 2.1 MHz, MICROCONTROLLER, PDIP40
MC68HC805C4CFN 8-BIT, EEPROM, 2.1 MHz, MICROCONTROLLER, PQCC44
MC68HC805K3DW 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PDSO16
相關代理商/技術參數
參數描述
MC68HC711K4CFN4 功能描述:IC MCU 24K OTP 4MHZ 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN,SCI,SPI 外圍設備:POR,PWM,溫度傳感器,WDT 輸入/輸出數:21 程序存儲器容量:40KB(20K x 16) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
MC68HC711K4CFNE3 制造商:Freescale Semiconductor 功能描述:
MC68HC711K4CFNE4 制造商:Freescale Semiconductor 功能描述:
MC68HC711K4CFU4 功能描述:IC MCU 24K 4MHZ EEPROM 80-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711KS2CPU4 制造商:Motorola Inc 功能描述: