- 您現在的位置：買賣IC網 > PDF目錄69028 > MC68HC711G5CFN (FREESCALE SEMICONDUCTOR INC) 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 PDF資料下載
參數資料
| 型號： | MC68HC711G5CFN |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| 封裝： | PLASTIC, LCC-84 |
| 文件頁數： | 109/195頁 |
| 文件大?。?/td> | 1940K |
| 代理商： | MC68HC711G5CFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁
OPERATING MODES AND SIGNAL DESCRIPTION
2-2
2.1.1
Single Chip Operating Mode
In single chip mode, the MCU functions as a self-contained microcontroller and has no external
address or data bus. This mode provides maximum use of the pins for on-chip peripheral functions
(66 pins). In single chip mode the R/W line is always high (read) to facilitate changing mode.
2.1.2
Expanded Non-Multiplexed Operating Mode
In the expanded non-multiplexed mode, the MCU can address up to 64 kbytes of address space.
High order address bits are output on Port B and low order address bits are output on Port F. The
bidirectional data bus is on Port C and the R/W pin is used to control the direction of data transfer
on this bus.
2.1.3
Bootstrap Operating Mode
This is a very versatile operating mode since there are essentially no limitations on the special
purpose program that can be loaded into internal RAM. The resident bootstrap program, contained
in the bootstrap ROM, uses the SCI to read a variable length program into on-chip RAM. Program
control is passed to RAM at location $0000 when an idle line of at least four characters occurs.
The MC68HC11G5 communicates through the SCI port. After reset in bootstrap mode, the SCI runs
at E/16 (7812 baud for E-clock = 2 MHz). A break condition is output on the SCI transmitter. For
normal use of the bootstrap program, the user must send $FF to the SCI receiver at either E/16 or
E/104 (1200 baud for E-clock = 2 MHz).
Note: The $FF is not echoed through the SCI transmitter.
In this mode all interrupt vectors are mapped to pseudo-vectors in RAM (refer to Table 2-2). This
allows programmers to use their own service-routine addresses. Each pseudo-vector is allowed
three bytes of space, rather than the two bytes for normal vectors, because an explicit jump (JMP)
opcode is needed to cause the desired jump to the user’s service-routine address.
Since the SMOD control bit is initialized to one, all of the privileged control bits are accessible in this
mode. This allows the bootstrap mode to be used for test and diagnostic functions on completed
modules. Mode switching can occur under program control by writing to the SMOD and MDA bits
of the HPRIO register.
2.1.4
Test Operating Mode
This special expanded mode is primarily intended for factory testing. In this mode the reset and
interrupt vectors are fetched externally from locations $BFFE – $BFFF. The SMOD bit in the HPRIO
register will be set, indicating that a special mode is in effect and allowing the user to write to certain
privileged control bits which are normally read-only bits. Also, a special register, TEST1, is enabled
which allows several factory test functions to be invoked.
It is also possible to change from the test mode to a normal operating mode by writing a zero to the
SMOD bit. Once this bit is cleared, it cannot be changed back to one without going through a reset
sequence.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11G7CFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84 |
| MC68HC711L6CFN1 | OTPROM, MICROCONTROLLER, PQCC68 |
| MC68HC805C4CP | 8-BIT, EEPROM, 2.1 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC805C4CFN | 8-BIT, EEPROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC805K3DW | 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC711K4CFN4 | 功能描述:IC MCU 24K OTP 4MHZ 84-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC711K4CFNE3 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFNE4 | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC711K4CFU4 | 功能描述:IC MCU 24K 4MHZ EEPROM 80-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| MC68HC711KS2CPU4 | 制造商:Motorola Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。