參數資料
型號: MC68HC05JB3JDW
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO28
封裝: SOIC-28
文件頁數: 124/148頁
文件大?。?/td> 1600K
代理商: MC68HC05JB3JDW
November 5, 1998
GENERAL RELEASE SPECIFICATION
MC68HC05JB3
UNIVERSAL SERIAL BUS MODULE
MOTOROLA
REV 1
10-9
Reset can wake a device from the suspended mode. A device may take up to
10ms to wake up from the suspended state.
10.2.3 Suspend
The MC68HC05JB3 supports suspend mode for low power. Suspend mode
should be entered when the USB data lines are in the idle state for more than 3.0
ms. Entry into Suspend mode is controlled by the SUSPND bit in the USB
Interrupt Register. Any low speed bus activity should keep the device out of the
suspend state. Low speed devices are kept awake by periodic low speed EOP
signals from the host. This is referred to as Low speed keep alive (refer to Section
11.2.5.1 of the USB specication).
Firmware should monitor the EOPF ag and enter suspend mode by setting the
SUSPND bit if an EOP is not detected for 3 ms.
Per the USB specication, the MC68HC05JB3 is required to draw less than
500
A from the V
DD supply when in the suspend state. This includes the current
supplied by the voltage regulator to the 15 K
to ground termination resistors
placed at the host end of the USB bus. This low current requirement means that
rmware is responsible for entering STOP mode once the USB module has been
placed in the suspend state.
10.2.4 Resume After Suspend
The MC68HC05JB3 can be activated from the suspend state by normal bus
activity, a USB reset signal, or by a forced resume driven from the
MC68HC05JB3.
10.2.4.1 Host Initiated Resume
The host signals resume by initiating resume signalling (“K” state) for at least 20
ms followed by a standard low speed EOP signal. This 20 ms ensures that all
devices in the USB network are awakened.
After resuming the bus, the host must begin sending bus trafc within 3 ms to
prevent the device from re-entering suspend mode.
10.2.4.2 USB Reset Signalling
Reset can wake a device from the suspended mode. A device may take up to 10
ms to wake up from the suspended state.
10.2.4.3 Remote Wake-up
The MC68HC05JB3 also supports the remote wake-up feature. The rmware has
the ability to exit suspend mode by signaling a resume state to the upstream Host
or Hub. A non-idle state (“K” state) on the USB data lines is accomplished by
asserting the FRESUM bit in the UCR1 register.
相關PDF資料
PDF描述
MC68HC05JB3JP 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDIP20
MC68HC05K3CSD 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDSO20
MC68HC05K3P 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP16
MC68HC05L25PB 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP52
MC68HC05LJ5P 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP16
相關代理商/技術參數
參數描述
MC68HC05JJ6 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers
MC68HC05JJ6CDW 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers
MC68HC05JJ6CDWE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers
MC68HC05JJ6CP 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers
MC68HC05JJ6CPE 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers