參數資料
型號: MC68HC05F32CFU
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 1.789 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 29/198頁
文件大?。?/td> 2335K
代理商: MC68HC05F32CFU
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁
MOTOROLA
11-16
MC68HC05F32
SERIAL COMMUNICATIONS INTERFACE
11
11.12
Baud rate selection
The exibility of the baud rate generator allows many different baud rates to be selected,
depending on the CPU clock frequency. A particular baud rate may be generated by manipulating
the various prescaler and division ratio bits.
The SCI baud rate can be calculated from the internal bus clock and the two prescaler factors,
PRS1 and PRS2. The rst prescaler factor, PRS1, is selected with SCP0 and SCP1, as shown in
Table 11-2. The second prescaler factor, PRS2, is selected with SCR0, SCR1 and SCR2, as
shown in Table 11-3. The SCI baud rate B equals the internal bus clock E, divided by 16, divided
by PRS1, divided by PRS2 (B = E/16/PRS1/PRS2).
Note:
For the receiver, the internal clock frequency is 16 times higher than the selected baud
rate.
11.13
SCI during STOP mode
When the MCU enters STOP mode, the baud rate generator driving the receiver and transmitter
is shut down. This stops all SCI activity. Both the receiver and the transmitter are unable to operate.
If the STOP instruction is executed during a transmitter transfer, that transfer is halted. When STOP
mode is exited as a result of an external interrupt, that particular transmission resumes.
If the receiver is receiving data when the STOP instruction is executed, received data sampling is
stopped (baud generator stops) and the rest of the data is lost.
Warning: For the above reasons, all SCI transactions should be in the idle state when the STOP
instruction is executed.
11.14
SCI during WAIT mode
The SCI system is not affected by WAIT mode and continues normal operation. Any valid SCI
interrupt will wake-up the system. If required, the SCI system can be disabled prior to entering
WAIT mode by writing a zero to the transmitter and receiver enable bits in the serial communication
control register 2 at $0049. This action will result in a reduction of power consumption during WAIT
mode.
TPG
118
05F32Book Page 16 Tuesday, June 8, 1999 7:55 am
相關PDF資料
PDF描述
MC68HC705H12 8-BIT, EEPROM, 2 MHz, MICROCONTROLLER, PQCC52
MC68HC705J1AVDWR2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HRC705J1ACDWR2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HSC705J1ACDWR2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20
MC68HRC705J1ADWR2 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
MC68HC05F32CPU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:a member of the M68HC05 family of HCMOS
MC68HC05F32FU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:a member of the M68HC05 family of HCMOS
MC68HC05F32PU 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:a member of the M68HC05 family of HCMOS
MC68HC05F4 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:MECHANICAL DATA
MC68HC05F5 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit