- 您現在的位置：買賣IC網 > PDF目錄45043 > M38198ECFS 8-BIT, UVPROM, 4.2 MHz, MICROCONTROLLER, CQCC100 PDF資料下載
參數資料
| 型號： | M38198ECFS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, 4.2 MHz, MICROCONTROLLER, CQCC100 |
| 封裝： | CERAMIC, LCC-100 |
| 文件頁數： | 178/218頁 |
| 文件大小： | 2137K |
| 代理商： | M38198ECFS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁當前第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁
48
3819 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
CLOCK GENERATING CIRCUIT
The 3819 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). Use the circuit constants in accordance
with the resonator manufacturer's recommended values. No exter-
nal resistor is needed between XIN and XOUT since a feed-back
resistor exists on-chip. However, an external feed-back resistor is
needed between XCIN and XCOUT.
Immediately after poweron, only the XIN oscillation circuit starts
oscillation, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
Middle-speed mode
The internal clock
φ is the frequency of XIN divided by 8. After re-
set, this mode is selected.
High-speed mode
The internal clock
φ is half the frequency of XIN.
Low-speed mode
The internal clock
φ is half the frequency of XCIN.
Note : If you switch the mode between middle/high-speed and low-speed,
stabilize both XIN and XCIN oscillations. The sufficient time is re-
quired for the XCIN oscillation to stabilize, especially immediately
after poweron and at returning from stop mode. When switching the
mode between middle/high-speed and low-speed, set the frequency
on condition that f(XIN) > 3f(XCIN).
Low-power dissipation mode
When stopping the main clock XIN in the low-speed mode, the low-
power dissipation operation starts. To stop the main clock, set the
bit 5 of the CPU mode register to “1”. When the main clock XIN is
restarted, set enough time for oscillation to stabilize by program-
ming.
The low-power dissipation operation 200
A or less (at f(XIN) = 32
kHz) can be realized by reducing the XCIN–XCOUT drivability. To re-
duce the XCIN–XCOUT drivability, clear the bit 3 of the CPU mode
register to “0”. At reset or when executing the STP instruction, this
bit is set to “1” and strong drivability is selected to help the oscilla-
tion to start.
Oscillation Control
Stop mode
If the STP instruction is executed, the internal clock
φ stops at an
“H” level, and XIN and XCIN oscillators stop. Timer 1 is set to “FF16”
and timer 2 is set to “0116”. Either XIN or XCIN divided by 16 is in-
put to timer 1, and the output of timer 1 is connected to timer 2.
The bits of the timer 12 mode register are cleared to “0”. Set the
timer 1 and timer 2 interrupt enable bits to disabled (“0”) before ex-
ecuting the STP instruction.
Oscillator restarts at reset or when an external interrupt is re-
ceived, but the internal clock
φ is not supplied to the CPU until
timer 1 underflows. When using an external resonator, it is neces-
sary for oscillating to stabilize.
Wait mode
If the WIT instruction is executed, the internal clock
φ stops at an
“H” level. The states of XIN and XCIN are the same as the state be-
fore executing the WIT instruction. The internal clock restarts at
reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the
clock is restarted.
Fig. 47 Ceramic resonator external circuit
Fig. 48 External clock input circuit
XCIN
XCOUT
CCIN
CCOUT
Rd
Rf
XIN
XOUT
CIN
COUT
XCIN
XCOUT
XIN
XOUT
Open
External oscillation
circuit or pulse
External oscillation
circuit
VCC
VSS
VCC
VSS
相關PDF資料 |
PDF描述 |
|---|---|
| M38199MF-XXXFP | 8-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP100 |
| M38199EFFP | 8-BIT, OTPROM, MICROCONTROLLER, PQFP100 |
| M38198EC-XXXFP | 8-BIT, OTPROM, MICROCONTROLLER, PQFP100 |
| M38199MF-XXXKP | 8-BIT, MROM, MICROCONTROLLER, PQFP100 |
| M38198MC-XXXKP | 8-BIT, MROM, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38198MCA809 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38198MCA824 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38198MCA827 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38199MF072F | 制造商:Panasonic Industrial Company 功能描述:IC |
| M38199MF210F | 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。