- 您現在的位置：買賣IC網 > PDF目錄69010 > M34506E4FP 4-BIT, OTPROM, MICROCONTROLLER, PDSO20 PDF資料下載
參數資料
| 型號： | M34506E4FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, MICROCONTROLLER, PDSO20 |
| 封裝： | 5.30 X 12.60 MM, 1.27 MM PITCH, PLASTIC, SOP-20 |
| 文件頁數： | 19/114頁 |
| 文件大小： | 937K |
| 代理商： | M34506E4FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
Rev.2.00
Aug 28, 2006
page 113 of 119
7643 Group
REJ03B0054-0200
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset
are undefined, except for the interrupt disable flag (I) which is “1”.
After a reset, initialize flags which affect program execution. In
particular, it is essential to initialize the index X mode (T) and the
decimal mode (D) flags because of their effect on calculations.
To reference the contents of the processor status register (PS),
execute the PHP instruction once then read the contents of
(S+1). If necessary, execute the PLP instruction to return the PS
to its original status.
A NOP instruction must be executed after every PLP instruction.
A SEI instruction must be executed before every PLP instruction.
A NOP instruction must be executed before every CLI instruction.
BRK Instruction
It can be detected that the BRK instruction interrupt event or the
least priority interrupt event by referring the stored B flag state.
Refer to the stored B flag state in the interrupt routine.
Decimal Calculations
When decimal mode is selected, the values of the V flags are in-
valid.
The carry flag (C) is set to “1” if a carry is generated as a result of
the calculation, or is cleared to “0” if a borrow is generated. To de-
termine whether a calculation has generated a carry, the C flag
must be initialized to “0” before each calculation. To check for a
borrow, the C flag must be initialized to “1” before each calcula-
tion.
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not af-
fect the MUL and DIV instruction.
Instruction Execution Time
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock
φ by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
Timers
If a value n (between 0 and 255) is written to a timer latch, the
frequency division ratio is 1/(n+1).
P51/XCOUT/TOUT pin cannot function as an I/O port when XCIN -
XCOUT is oscillating. When XCIN - XCOUT oscillation is not used or
XCOUT oscillation drive is disabled, this pin can function as the
TOUT output pin of the timer 1 or 2.
When using the TOUT output function and f(XCIN) divided by 2 is
used as the timer 1 count source (bit 2 of T123M = “1”), disable
XCOUT oscillation drive (bit 5 of CCR = “1”).
Ports
When the data register (port latch) of an I/O port is modified with
the bit managing instruction (SEB, CLB instructions) the value of
the unspecified bit may be changed.
In standby state (the stop mode by executing the STP instruction,
and the wait mode by executing the WIT instruction) for low-
power dissipation, do not make input levels of an I/O port
“undefined”, especially for I/O ports of the P-channel and the N-
channel open-drain.
Pull-up (connect the port to Vcc) or pull-down (connect the port to
Vss) these ports through a resistor.
When determining a resistance value, note the following points:
(1) External circuit
(2) Variation of output levels during the ordinary operation
When using built-in pull-up or pull-down resistor, note on varied
current values.
(1) When setting as an input port : Fix its input level
(2) When setting as an output port : Prevent current from flowing
out to external
Serial I/O
Do not write to the serial I/O shift register during a transfer when in
SPI compatible mode.
UART
The all error flags PER, FER, OER and SER are cleared to “0”
when the UART status register is read, at the hardware reset or
initialization by setting the Transmit Initialization Bit. These flags
are also cleared to “0” by execution of bit test instructions such as
BBC and BCS.
The transmission interrupt request bit might be set and the inter-
rupt request is generated by setting the transmit initialization bit
to “1” even when selecting timing that either of the following flags
is set to “1” as timing where the transmission interrupt is gener-
ated:
(1) Transmit buffer empty flag is set to “1”
(2) Transmit complete flag is set to “1”.
Therefore, when the transmit interrupt is used, set the transmit in-
terrupt enable bit to transmit enabled as the following sequence:
(1) Transmit initialization bit is set to “1”
(2) Transmit interrupt request bit is set to “0”
(3) Transmit interrupt enable bit is set to “1”.
Do not update a value of UART baud rate generator in the condi-
tion of transmission enabled or reception enabled. Disable
transmission and reception before updating the value. If the
former data remains in the UART transmit buffer registers 1 and 2
when transmission is enabled, an undefined data might be out-
put.
相關PDF資料 |
PDF描述 |
|---|---|
| M34508G4HFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
| M34508G4GP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
| M34508G4H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
| M34508G4-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
| M34508G4FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34506M2 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34506M2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES |
| M34506M4 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34506M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 4500 SERIES |
| M34507E4FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。