參數資料
型號： LPC2926FBD144
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： ARM9 microcontroller with CAN, LIN, and USB
中文描述： 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP144
封裝： 20 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT486-1, LQFP-144
文件頁數： 29/95頁
文件大?。?/td> 1855K
代理商： LPC2926FBD144
LPC2926_27_29
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 5 — 28 September 2010
29 of 95
NXP Semiconductors
LPC2926/2927/2929
ARM9 microcontroller with CAN, LIN, and USB
6.12 General subsystem
6.12.1
General subsystem clock description
The general subsystem is clocked by CLK_SYS_GESS, see
Section 6.7.2
.
6.12.2
Chip and feature identification
The Chip/Feature ID (CFID) module contains registers which show and control the
functionality of the chip. It contains an ID to identify the silicon and also registers
containing information about the features enabled or disabled on the chip.
The key features are:
Identification of product
Identification of features enabled
The CFID has no external pins.
6.12.3
System Control Unit (SCU)
The system control unit contains system-related functions. The key feature is
configuration of the I/O port-pins multiplexer. It defines the function of each I/O pin of the
LPC2926/2927/2929. The I/O pin configuration should be consistent with peripheral
function usage.
The SCU has no external pins.
6.12.4
Event router
The event router provides bus-controlled routing of input events to the vectored interrupt
controller for use as interrupt or wake-up signals.
Key features:
Up to 20 level-sensitive external interrupt pins, including the receive pins of SPI, CAN,
LIN, USB, and UART, as well as the I
2
C-bus SCL pins plus three internal event
sources.
Input events can be used as interrupt source either directly or latched
(edge-detected).
Direct events disappear when the event becomes inactive.
Latched events remain active until they are explicitly cleared.
Programmable input level and edge polarity.
Event detection maskable.
Event detection is fully asynchronous, so no clock is required.
The event router allows the event source to be defined, its polarity and activation type to
be selected and the interrupt to be masked or enabled. The event router can be used to
start a clock on an external event.
The vectored interrupt-controller inputs are active HIGH.
相關PDF資料
PDF描述
LPC2927FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2929FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2930FBD208 ARM9 flashless microcontroller with CAN, LIN, and USB
LPC2939FBD208 ARM9 microcontroller with CAN, LIN, and USB
LPC3180FEL320 16-32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface
相關代理商/技術參數
參數描述
LPC2926FBD144,557 制造商:NXP Semiconductors 功能描述:LPC2926FBD144/LQFP144/TRAYDPM/ - Trays 制造商:NXP Semiconductors 功能描述:IC MCU ARM9 256KB FLASH 144LQFP
LPC2927 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2927_10 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2927FBD144 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2927FBD144,551 功能描述:ARM微控制器 - MCU ARM968 512K FL/16K RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*