參數資料
型號: LPC2925FBD100
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: ARM9 microcontroller with CAN, LIN, and USB
中文描述: 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP100
封裝: 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT407-1, LQFP-100
文件頁數: 39/84頁
文件大小: 551K
代理商: LPC2925FBD100
LPC2921_23_25_3
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 03 — 14 April 2010
39 of 84
NXP Semiconductors
LPC2921/2923/2925
ARM9 microcontroller with CAN, LIN, and USB
6.14.6.1
Pin description
MSCSS timer 0 has no external pins.
MSCSS timer 1 has a PAUSE pin available as external pin. The PAUSE pin is combined
with other functions on the port pins of the LPC2921/2923/2925.
Table 22
shows the
MSCSS timer 1 external pin.
Table 22.
Symbol
MSCSS PAUSE
6.14.6.2
Clock description
The timer modules in the MSCSS are clocked by CLK_MSCSS_MTMRx (x = 0 to 1), see
Section 6.7.2
. Note that each timer has its own CLK_MSCSS_MTMRx branch clock for
power management. The frequency of all these clocks is identical to CLK_MSCSS_APB
since they are derived from the same base clock BASE_MSCSS_CLK.
Note that, unlike the timer modules in the Peripheral SubSystem, the actual timer counter
registers run at the same clock as the APB system interface CLK_MSCSS_APB. This
clock is independent of the AHB system clock.
If a timer module is not used its CLK_MSCSS_MTMRx branch clock can be switched off.
6.14.7
Quadrature Encoder Interface (QEI)
A quadrature encoder, also known as a 2-channel incremental encoder, converts angular
displacement into two pulse signals. By monitoring both the number of pulses and the
relative phase of the two signals, the user can track the position, direction of rotation, and
velocity. In addition, a third channel, or index signal, can be used to reset the position
counter. The quadrature encoder interface decodes the digital pulses from a quadrature
encoder wheel to integrate position over time and determine direction of rotation. In
addition, the QEI can capture the velocity of the encoder wheel.
The QEI has the following features:
Tracks encoder position.
Increments/decrements depending on direction.
Programmable for 2
×
or 4
×
position counting.
Velocity capture using built-in timer.
Velocity compare function with less than interrupt.
Uses 32-bit registers for position and velocity.
Three position compare registers with interrupts.
Index counter for revolution counting.
Index compare register with interrupts.
Can combine index and position interrupts to produce an interrupt for whole and
partial revolution displacement.
Digital filter with programmable delays for encoder input signals.
Can accept decoded signal inputs (clk and direction).
Connected to APB.
MSCSS timer 1 pin
Direction
IN
Description
pause pin for MSCSS timer 1
相關PDF資料
PDF描述
LPC2926FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2927FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2929FBD144 ARM9 microcontroller with CAN, LIN, and USB
LPC2930FBD208 ARM9 flashless microcontroller with CAN, LIN, and USB
LPC2939FBD208 ARM9 microcontroller with CAN, LIN, and USB
相關代理商/技術參數
參數描述
LPC2925FBD100,551 功能描述:ARM微控制器 - MCU IC ARM9 MCU FLASH 512KB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2926 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2926FBD144 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB
LPC2926FBD144,557 制造商:NXP Semiconductors 功能描述:LPC2926FBD144/LQFP144/TRAYDPM/ - Trays 制造商:NXP Semiconductors 功能描述:IC MCU ARM9 256KB FLASH 144LQFP
LPC2927 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN, LIN, and USB