參數資料
型號： L6566BTR
廠商： 意法半導體
英文描述： Multi-mode controller for SMPS
中文描述： 多模式開關電源控制器
文件頁數： 21/51頁
文件大?。?/td> 401K
代理商： L6566BTR
L6566B
Application information
21/51
5.2
Zero current detection and triggering block; oscillator block
The Zero Current Detection (ZCD) and Triggering blocks switch on the external MOSFET if
a negative-going edge falling below 50 mV is applied to the input (pin 11, ZCD). To do so the
triggering block must be previously armed by a positive-going edge exceeding 100 mV.
This feature is typically used to detect transformer demagnetization for QR operation, where
the signal for the ZCD input is obtained from the transformer’s auxiliary winding used also to
supply the L6566B. The triggering block is blanked for T
BLANK
= 2.5 μs after MOSFET’s turn-
off to prevent any negative-going edge that follows leakage inductance demagnetization
from triggering the ZCD circuit erroneously.
The voltage at the pin is both top and bottom limited by a double clamp, as illustrated in the
internal diagram of the ZCD block of
Figure 8 on page 20
. The upper clamp is typically
located at 5.7 V, while the lower clamp is located at -0.4V. The interface between the pin and
the auxiliary winding will be a resistor divider. Its resistance ratio will be properly chosen
(see
Section 5.11: OVP block on page 35
) and the individual resistance values (R
Z1
, R
Z2
)
will be such that the current sourced and sunk by the pin be within the rated capability of the
internal clamps (
±
3 mA).
At converter power-up, when no signal is coming from the ZCD pin, the oscillator starts up
the system. The oscillator is programmed externally by means of a resistor (R
T
) connected
from pin OSC (13) to ground. With good approximation the oscillation frequency f
osc
will be:
Equation 2
(with f
osc
in kHz and R
T
in k
). As the device is turned on, the oscillator starts immediately;
at the end of the first oscillator cycle, being zero the voltage on the ZCD pin, the MOSFET
will be turned on, thus starting the first switching cycle right at the beginning of the second
oscillator cycle. At any switching cycle, the MOSFET is turned off as the voltage on the
current sense pin (CS, 7) hits an internal reference set by the Line Feedforward block, and
the transformer starts demagnetization. If this completes (hence a negative-going edge
appears on the ZCD pin) after a time exceeding one oscillation period T
osc
=1/f
osc
from the
previous turn-on, the MOSFET will be turned on again - with some delay to ensure minimum
voltage at turn-on – and the oscillator ramp will be reset. If, instead, the negative-going edge
appears before T
osc
has elapsed, it will be ignored and only the first negative-going edge
after T
osc
will turn-on the MOSFET and synchronize the oscillator. In this way one or more
drain ringing cycles will be skipped (“valley-skipping mode”,
Figure 9
) and the switching
frequency will be prevented from exceeding f
osc
.
T
3
osc
f
R
10
2
≈
相關PDF資料
PDF描述
L6567 HIGH VOLTAGE DRIVER FOR CFL
L6567D HIGH VOLTAGE DRIVER FOR CFL
L6571B High Voltage Half Bridge Driver with Oscillator(帶晶振的高電壓半橋驅動器)
L6585D PFC and Ballast Control IC
L6585DTR PFC and Ballast Control IC
相關代理商/技術參數
參數描述
L6566BTR-CUT TAPE 制造商:ST 功能描述:L6566B Series 23 V 4.6 mA SMPS Multi-Mode Controller Surface Mount - SOIC-16N
L6567 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:HIGH VOLTAGE DRIVER FOR CFL
L6567D 制造商:STMicroelectronics 功能描述:CFL DRVR 18V 14SOP - Rail/Tube
L6569 功能描述:功率驅動器IC Hi-Volt Half Bridge RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L6569 制造商:STMicroelectronics 功能描述:IC HALF BRIDGE+OSC 6569 DIP8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*