- 您現在的位置：買賣IC網 > PDF目錄383236 > L6256 (意法半導體) 12V COMBO PDF資料下載
參數資料
| 型號： | L6256 |
| 廠商： | 意法半導體 |
| 英文描述： | 12V COMBO |
| 中文描述： | 12V的組合 |
| 文件頁數： | 26/28頁 |
| 文件大小： | 258K |
| 代理商： | L6256 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
RESYNC ALGORITHM
The firmware must use start mode to resync the
back EMF signal when attempting to resynchron-
ize the spindle speed. Please consult the Motion
Control Group for more details. The spinup algo-
rithm is available as a separate specification.
DESIGN FORMULAS
Spindle startup current
Spindle startup current is set up using the follow-
ing formula:
Imax = Rref
1.6
62.5k in amps
The Vcc tolerances are added to the final design
value.
Back EMF window width
Window width is calculated for other than the
nominal conditions by ratioing the window voltage
against the current nominal design point:
tw
=
25
Rref
Rref
+
Rref
62.5
+
120
62.5
8V
Vemf
6000
RPM
Where:
Vemf is the nominal expected back emf to peak
voltage, RPM is the target RPM of the drive;
tw is the resultatnt window width.
If the window is too small or too large, transients
will affect the detection.
CHOPPING WAVEFORM
There is a requirement on the back EMF wave-
form. The chopping transients must die out be-
fore the waveform is sampled or speed errors will
result.
This puts limits on the damping resistors if pre-
sent, which depend on motor inductance, eddy
current losses and the like.
SH_OUT COMPONENTS
The SH_Out components must be designed so
that the rate of droop of the capacitor matches
the back EMF waveform at its negative going
zero crossing point when the drive is on speed.
Components for one part will work for the other
part, but voltage waveforms are scaled differently
between the two parts.
The SH_Out resistor should be as large as possi-
ble. This minimizes the internal impedances and
sample/hold errors. 100K is the nominal design
point.
Additional design formuals are included in the
applications notes for each vendor’s parts and in
Western Digital’s internal application notes.
L6256
26/28
相關PDF資料 |
PDF描述 |
|---|---|
| L6258E | PWM CONTROLLED - HIGH CURRENT DMOS UNIVERSAL MOTOR DRIVER |
| L6258EX | PWM CONTROLLED - HIGH CURRENT DMOS UNIVERSAL MOTOR DRIVER |
| L6260 | 4.5 - 5.5V DISK DRIVER SPINDLE & VCM, POWER & CONTROL COMBO’S |
| L6268 | 12V DISK DRIVE SPINDLE & VCM, POWER & CONTROL “COMBO” |
| L6269 | 12V DISK DRIVE SPINDLE & VCM, POWER & CONTROL “COMBO” |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6258 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
| L6258_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
| L6258A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Stepper Motor Controller/Driver |
| L6258E | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6258E_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:PWM controlled high current DMOS universal motor driver |
發布緊急采購，3分鐘左右您將得到回復。