- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82V2082BFG (IDT, Integrated Device Technology Inc)IC LIU T1/E1/J1 2CH 81BGA PDF資料下載
參數資料
| 型號： | IDT82V2082BFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 29/88頁 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 2CH 81BGA |
| 標準包裝： | 360 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.13 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 81-LFBGA |
| 供應商設備封裝： | 81-CABGA（8x8） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
IDT82V2082
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
FUNCTIONAL DESCRIPTION
35
May 4, 2009
3.7
TRANSMIT AND DETECT INTERNAL PATTERNS
The internal patterns (All Ones, All Zeros, PRBS/QRSS pattern and
Activate/Deactivate Loopback Code) will be generated and detected by
IDT82V2082. TCLKn is used as the reference clock by default. MCLK can
also be used as the reference clock by setting the PATT_CLK bit (MAINT0,
0CH...) to ‘1’.
If the PATT_CLK bit (MAINT0, 0CH...) is set to ‘0’ and the PATT[1:0] bits
(MAINT0, 0CH...) are set to ‘00’, the transmit path will operate in normal
mode.
When the chip is configured by hardware, the transmit path will operate
in normal mode by setting PATTn[1:0] pins to ‘00’ on a per channel basis.
Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.7.1
TRANSMIT ALL ONES
In transmit direction, the All Ones data can be inserted into the data
stream when the PATT[1:0] bits (MAINT0, 0CH...) are set to ‘01’. The trans-
mit data stream is output from TTIPn/TRINGn. In this case, either TCLKn
or MCLK can be used as the transmit clock, as selected by the PATT_CLK
bit (MAINT0, 0CH...).
Inhardwarecontrolmode,theAllOnesdatacanbeinsertedintothedata
stream in transmitdirectionby settingPATTn[1:0] pins to ‘01’ on aperchan-
nel basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.7.2
TRANSMIT ALL ZEROS
If the PATT_CLK bit (MAINT0, 0CH...) is set to ‘1’, the All Zeros will be
inserted into the transmit data stream when the PATT[1:0] bits (MAINT0,
0CH...) are set to ‘00’.
3.7.3
PRBS/QRSS GENERATION AND DETECTION
A PRBS/QRSS will be generated in the transmit direction and detected
in the receive direction by IDT82V2082. The QRSS is 220-1 for T1/J1 appli-
cations and the PRBS is 215-1 for E1 applications, with maximum zero
restrictions according to the AT&T TR62411 and ITU-T O.151.
When the PATT[1:0] bits (MAINT0, 0CH...) are set to ‘10’, the PRBS/
QRSS pattern will be inserted into the transmit data stream with the MSB
first. The PRBS/QRSS pattern will be transmitted directly or invertedly.
In hardware control mode, the PRBS data will be generated in the trans-
mit direction and inserted into the transmit data stream by setting
PATTn[1:0] pins to ‘10’ on a per channel basis. Refer to 5HARDWARECON-
for details.
The PRBS/QRSS in the received data stream will be monitored. If the
PRBS/QRSS has reached synchronization status, the PRBS_S bit
(STAT0, 16H...) will be set to ‘1’, even in the presence of a logic error rate
less than or equal to 10-1. The criteria for setting/clearing the PRBS_S bit
are shown in Table-20.
PRBS data canbe inverted throughsetting the PRBS_INVbit(MAINT0,
0CH...).
Any change of PRBS_S bit will be captured by PRBS_IS bit (INTS0,
18H...). The PRBS_IES bit (INTES, 15H...) can be used to determine
whetherthe ‘0’ to‘1’changeof PRBS_Sbitwill becapturedby thePRBS_IS
bitoranychangesofPRBS_SbitwillbecapturedbythePRBS_ISbit.When
the PRBS_IS bit is ‘1’, an interrupt will be generated if the PRBS_IM bit
(INTM0, 13H...) is set to ‘1’.
The received PRBS/QRSS logic errors can be counted in a 16-bit
counter if the ERR_SEL [1:0] bits (MAINT6, 12H...) are set to ‘00’. Refer to
3.9 ERROR DETECTION/COUNTING AND INSERTION for the operation
of the error counter.
3.8
LOOPBACK
To facilitate testing and diagnosis, the IDT82V2082 provides four dif-
ferent loopback configurations: Analog Loopback, Digital Loopback,
Remote Loopback and Inband Loopback.
3.8.1
ANALOG LOOPBACK
WhentheALPbit(MAINT1,0DH...)issetto‘1’,thecorrespondingchan-
nel is configured in Analog Loopback mode. In this mode, the transmit sig-
nals are looped back to the Receiver Internal Termination in the receive
path then output from RCLKn, RDn, RDPn/RDNn. The all-ones pattern can
be generated during analog loopback. At the same time, the transmit sig-
nalsarestilloutputtoTTIPn/TRINGnintransmitdirection.Figure-15shows
the process.
In hardware control mode, Analog Loopback can be selected by setting
LPn[1:0] pins to ‘01’ on a per channel basis.
3.8.2
DIGITAL LOOPBACK
WhentheDLPbit(MAINT1,0DH...)issetto‘1’,thecorrespondingchan-
nel is configured in Digital Loopback mode. In this mode, the transmit sig-
nals are looped back to the jitter attenuator (if enabled) and decoder in
receive path, then output from RCLKn, RDn, RDPn/RDNn. At the same
time, the transmit signals are still output to TTIPn/TRINGn in transmit direc-
tion. Figure-16 shows the process.
Both Analog Loopback mode and Digital Loopback mode allow the
sending of the internal patterns (All Ones, All Zeros, PRBS, etc.) which will
overwrite the transmit signals. In this case, either TCLKn or MCLK can be
used as the reference clock for internal patterns transmission.
In hardware control mode, Digital Loopback can be selected by setting
LPn[1:0] pins to ‘10’ on a per channel basis.
Table-20 Criteria for Setting/Clearing the PRBS_S Bit
PRBS/QRSS
Detection
6 or less than 6 bit errors detected in a 64 bits hopping win-
dow.
PRBS/QRSS
Missing
More than 6 bit errors detected in a 64 bits hopping window.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82V2084PFG | IC LIU T1/J1/E1 4CH 128-TQFP |
| IDT82V2088DRG | IC LIU T1/J1/E1 8CH 208-TQFP |
| IDT82V2108BBG | IC FRAMER T1/J1/E1 8CH 144-BGA |
| IDT82V2604BBG | IC INVERSE MUX 4CH ATM 208-BGA |
| IDT82V2608BBG | IC INVERSE MUX 8CH ATM 208-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V2082BFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 2CH 81BGA |
| IDT82V2082BFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT |
| IDT82V2082PF | 功能描述:IC LIU T1/J1/E1 2CH 80-TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2082PF8 | 功能描述:IC LIU T1/J1/E1 2CH 80-TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82V2082PFBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。