- 您現在的位置：買賣IC網 > PDF目錄383075 > HSP50214B (Intersil Corporation) Programmable Downconverter PDF資料下載
參數資料
| 型號： | HSP50214B |
| 廠商： | Intersil Corporation |
| 英文描述： | Programmable Downconverter |
| 中文描述： | 可編程變頻器 |
| 文件頁數： | 38/60頁 |
| 文件大?。?/td> | 573K |
| 代理商： | HSP50214B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
3-38
The FIFO mode allows the processor to service the interface
only when enough samples are present in the RAM. This
mode is provided so that the
μ
Processor does not have to
service the PDC every output sample. An interrupt,
INTRRPT, is asserted when the desired number of samples
are available. The PDC can be programmed to assert the
interrupt when up to 7 samples are available. Control Word
21, Bit 15 is used to set the Buffer RAM controller to the
FIFO mode, while Control Word 21, Bits 12-14 set the
number of RAM samples to be stored (0 to 7) before the
interrupt (INTRRPT) is asserted. Control Word 20, Bit 24
determines whether the RAM output interface is the 8-bit
microprocessor interface or the 16-bit processor interface. In
the 16-bit interface the MSByte is sent to AOUT(7:0) while
the LSByte is sent to BOUT(7:0).
The INTRRP output signal goes low for 8 PROCCLK cycles
when the number of samples in the Buffer RAM (depth)
reaches the programmed depth. The depth of the RAM is
calculated using Equation 23. A DSP microprocessor or the
data processing engine can use the INTRRP signal to know
that the RAM is ready to be read.
FIFO Operation via 16-Bit
μ
Processor
Interface
Figure 37 shows the conceptual configuration of the 16-bit
μ
Processor interface. This interface looks like a 16-bit
μ
Processor read-only microprocessor interface. The
SEL(2:0) lines are the address bus and the OEAL and OEBL
lines are the read lines. The address is decoded as shown in
Table 17.
Use of the 16-bit interface for Buffer RAM output requires
Control Word 20, Bit 25, to be set to a logic “0” and Control
Word 20, Bit 24, to be set to a logic “1”. Once the Control
Word 20 has been set to route data to AOUT(7:0) and
BOUT(7:0), then the microprocessor must place a value on
the PDC input pins SEL(2:0), to choose which data type will
be output on AOUT(7:0) and 6BOUT(7:0). Table 17 defines
the data types in terms of SEL(2:0). With the control lines
set, the selected data is read MSByte on AOUT(7:0) and
LSByte on BOUT(7:0) when OEAL and OEBL (are low).
New data only read when OEBL goes low, so use
μ
P for 8-
bit modes. Programming SEL(2:0) = 110 outputs a 16-bit
status signal on AOUT and BOUT. The FIFO status includes
FULL, EMPTY, FIFO Depth, and READYB. These status
signals are defined in Table 18.
(EQ. 23)
D
RAM
ADDR
WRITE
ADDR
READ
–
(
)
1
]
MOD8
–
[
=
TABLE 17. BUFFER RAM OUTPUT SELECT DEFINITIONS
SEL(2:0)
OUTPUT DATA TYPE
000
I Data
001
Q Data
010
Magnitude
011
Phase
100
Frequency
101
Unused
110
Memory Status
111
Reading
this address increments to the next
sample set
TABLE 18. STATUS BIT DEFINITIONS
AOUT BIT
LOCATION
INFORMATION
(7:5)
FIFO depth - When in FIFO mode, these bits
are the current depth of the FIFO.
4
EMPTY - When in FIFO mode, the FIFO is
empty, and the read pointer cannot be ad-
vanced. Active High.
3
FULL - When in FIFO mode, the FIFO is full,
and new samples will not be written.
Active High.
2
READYB - When in FIFO mode, the output buff-
er has reached the programmed threshold. In
the snapshot mode, the programmed number
of samples have been taken. Active Low.
1-0
GND
NOTE: In the Status output, BOUT(7:0) are all GND.
FIGURE 37. 16-BIT MICROPROCESSOR INTERFACE BUFFER
RAM MODE BLOCK DIAGRAM
|r|
φ
Q
DUAL
PORT
RAM
16
ADDRESS
SEQUENCER
INCR
WR
“SET OF WORDS”
16
16
16
D
D
16
I
RD
INCR
WRITE
SEQUENCER
|r|
φ
STATUS
Q
I
0
1
2
3
4
6
OEBL
SEL(2:0)
NEW
DATA
OUTPUT
DATA
M
M
PROCCLK
HSP50214B
相關PDF資料 |
PDF描述 |
|---|---|
| HSP50214BVC | Programmable Downconverter |
| HSP50214BVI | Programmable Downconverter |
| HT84 | ADSL Coupling Transformers |
| HT84-00594 | ADSL Coupling Transformers |
| HT8400594S | ADSL Coupling Transformers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSP50214B_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable Downconverter |
| HSP50214BVC | 功能描述:上下轉換器 120L MQFP COMTEMP 14-BIT PROGRAMMABLE DOWNCONVERTER 65MSPS RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| HSP50214BVCZ | 功能描述:上下轉換器 120L MQFP COMTEMP 14-BIT PROG DWNCNVRT RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| HSP50214BVI | 功能描述:上下轉換器 120L MQFP INDTEMP 14-BIT PROGRAMMABLE DOWNCONVERTER 65MSPS RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| HSP50214BVIZ | 功能描述:上下轉換器 120L MQFP INDTEMP 14-BIT PROG DWNCNVRT RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
發布緊急采購，3分鐘左右您將得到回復。