參數資料
型號： EVAL-ADUC7126QSPZ
廠商： Analog Devices Inc
文件頁數： 92/108頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR ADUC7126
設計資源： EVAL-ADUC7126 Schematic
ADUC7126 Gerber Files
標準包裝： 1
系列： MicroConverter® ADuC7xxx
類型： MCU
適用于相關產品： ADUC7126
所含物品： 板
ADuC7124/ADuC7126
Data Sheet
Rev. C | Page 84 of 108
PROCESSOR REFERENCE PERIPHERALS
INTERRUPT SYSTEM
There are 25 interrupt sources on the ADuC7124/ADuC7126
that are controlled by the interrupt controller. All interrupts
are generated from the on-chip peripherals, except for the
software interrupt (SWI), which is programmable by the user.
The ARM7TDMI CPU core recognizes interrupts as one of
two types: a normal interrupt request (IRQ) and a fast interrupt
request (FIQ). All the interrupts can be masked separately.
The control and configuration of the interrupt system is
managed through a number of interrupt-related registers. The
bits in each IRQ and FIQ register represent the same interrupt
source as described in Table 126.
The ADuC7124/ADuC7126 contain a vectored interrupt control-
ler (VIC) that supports nested interrupts up to eight levels. The
VIC also allows the programmer to assign priority levels to all
interrupt sources. Interrupt nesting must be enabled by setting
the ENIRQN bit in the IRQCONN register. A number of extra
MMRs are used when the full-vectored interrupt controller is
enabled.
IRQSTA/FIQSTA should be saved immediately upon entering
the interrupt service routine (ISR) to ensure that all valid
interrupt sources are serviced.
Table 126. IRQ/FIQ MMRs Bit Descriptions
Bit
Description
Comments
0
All interrupts OR’ed
(FIQ only)
This bit is set if any FIQ is active.
1
Software interrupt
User programmable interrupt
source.
2
Timer0
General-Purpose Timer 0.
3
Timer1
General-Purpose Timer 1.
4
Timer2 or wake-up
timer
General-Purpose Timer 2 or
wake-up timer.
5
Timer3 or watchdog
timer
General-Purpose Timer 3 or
watchdog timer.
6
Flash Control 0
Flash controller for Block 0
interrupt.
7
Flash Control 1
Flash controller for Block 1
interrupt.
8
ADC
ADC interrupt source bit.
9
UART0
UART0 interrupt source bit.
10
UART1
UART1 interrupt source bit.
11
PLL lock
PLL lock bit.
12
I2C0 master IRQ
I2C master interrupt source bit.
13
I2C0 slave IRQ
I2C slave interrupt source bit.
14
I2C1 master IRQ
I2C master interrupt source bit.
15
I2C1 slave IRQ
I2C slave interrupt source bit.
16
SPI
SPI interrupt source bit.
17
XIRQ0 (GPIO IRQ0 )
External Interrupt 0.
18
Comparator
Voltage comparator source bit.
19
PSM
Power supply monitor.
20
XIRQ1 (GPIO IRQ1)
External Interrupt 1.
Bit
Description
Comments
21
PLA IRQ0
PLA Block 0 IRQ bit.
22
XIRQ2 (GPIO IRQ2 )
External Interrupt 2.
23
XIRQ3 (GPIO IRQ3)
External Interrupt 3.
24
PLA IRQ1
PLA Block 1 IRQ bit.
25
PWM
PWM trip interrupt source bit.
IRQ
The IRQ is the exception signal to enter the IRQ mode of the
processor. It services general-purpose interrupt handling of
internal and external events.
All 32 bits are logically OR’ed to create a single IRQ signal to the
ARM7TDMI core. Descriptions of the four 32-bit registers
dedicated to IRQ follow.
IRQSTA Register
IRQSTA is a read-only register that provides the current-enabled
IRQ source status (effectively a logic AND of the IRQSIG and
IRQEN bits). When set to 1, that source generates an active IRQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
IRQSTA Register
Name:
IRQSTA
Address:
0xFFFF0000
Default Value:
0x00000000
Access:
Read only
IRQSIG Register
IRQSIG reflects the status of the various IRQ sources. If a periph-
eral generates an IRQ signal, the corresponding bit in the
IRQSIG is set; otherwise, it is cleared. The IRQSIG bits clear
when the interrupt in the particular peripheral is cleared. All
IRQ sources can be masked in the IRQEN MMR. IRQSIG is
read only. This register should not be used in an interrupt
service routine for determining the source of an IRQ exception;
IRQSTA should only be used for this purpose.
IRQSIG Register
Name:
IRQSIG
Address:
0xFFFF0004
Default Value:
0x00000000
Access:
Read only
相關PDF資料
PDF描述
REC5-243.3SRWZ/H4/A CONV DC/DC 5W 9-36VIN 3.3VOUT
EVAL-ADUC7023QSPZ KIT DEV FOR ADUC7023 QUICK START
RPS-1K-6-250/2.0-9 HEAT SHRINK SLEEVE
ECM30DCWH CONN EDGECARD 60POS DIP .156 SLD
SC43B-3R3 INDUCTOR SMD 3.3UH 1.44A 7.96MHZ
相關代理商/技術參數
參數描述
EVAL-ADUC7128QSPZ 功能描述:KIT DEV FOR ADUC7128 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7128QSPZ2 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
EVAL-ADUC7129QSPZ 制造商:Analog Devices 功能描述:- Bulk
EVAL-ADUC812QS 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM
EVAL-ADUC812QSP 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter㈢, Multichannel 12-Bit ADC with Embedded Flash MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*