參數資料
型號： EVAL-AD7731EB
廠商： Analog Devices, Inc.
英文描述： Low Noise, High Throughput 24-Bit Sigma-Delta ADC
中文描述： 低噪聲，高吞吐量的24位Σ-Δ模數轉換器
文件頁數： 8/44頁
文件大?。?/td> 411K
代理商： EVAL-AD7731EB
AD7731
–8–
REV. 0
PIN FUNCT ION DE SCRIPT IONS (Continued)
Pin
No.
Pin
Mnemonic
Function
3
MCLK OUT
When the master clock for the device is a crystal/resonator, the crystal/resonator is connected between
MCLK IN and MCLK OUT . If an external clock is applied to the MCLK IN, MCLK OUT provides an
inverted clock signal. T his clock can be used to provide a clock source for external circuits and MCLK OUT
is capable of driving one CMOS load.
Clock Polarity. Logic Input. T his determines the polarity of the serial clock. If the active edge for the proces-
sor is a high-to-low SCLK transition, this input should be low. In this mode, the AD7731 puts out data on
the DAT A OUT line in a read operation on a low-to-high transition of SCLK and clocks in data from the
DAT A IN line in a write operation on a high-to-low transition of SCLK. In applications with a noncontinuous
serial clock (such as most microcontroller applications), this means that the serial clock should idle low
between data transfers. If the active edge for the processor is a low-to-high SCL K transition, this input
should be high. In this mode, the AD7731 puts out data on the DAT A OUT line in a read operation on a
high-to-low transition of SCLK and clocks in data from the DAT A IN line in a write operation on a low-to-
high transition of SCLK . In applications with a noncontinuous serial clock (such as most microcontroller
applications), this means that the serial clock should idle high between data transfers.
Logic Input that allows for synchronization of the digital filters and analog modulators when using a number
of AD7731s. While
SYNC
is low, the nodes of the digital filter, the filter control logic and the calibration
control logic are reset and the analog modulator is also held in its reset state.
SYNC
does not affect the
digital interface but does reset
RDY
to a high state if it is low. While
SYNC
is asserted, the Mode Bits may
be set up for a subsequent operation that will commence when the
SYNC
pin is deasserted.
Logic Input. Active low input that resets the control logic, interface logic, digital filter, analog modulator and
all on-chip registers of the part to power-on status. Effectively, everything on the part except for the clock
oscillator is reset when the
RESET
pin is exercised.
No Connect. T he user is advised not to connect anything to this pin.
Ground reference point for analog circuitry.
Analog Positive Supply Voltage. T he AV
DD
to AGND differential is 5 V nominal.
Analog Input Channel 1. Programmable-gain analog input that can be used as a pseudo-differential input
when used with AIN6 or as the positive input of a differential pair when used with AIN2.
Analog Input Channel 2. Programmable-gain analog input that can be used as a pseudo-differential input
when used with AIN6 or as the negative input of a differential pair when used with AIN1.
Analog Input Channel 3 or Digital Output 1. T his pin can be used as either an analog input or a digital
output bit as determined by the DEN bit of the Mode Register. When selected as a programmable-gain
analog input, it can be used as a pseudo-differential input when used with AIN6 or as the positive input of a
differential pair when used with AIN4. When selected as a digital output, this output can be programmed
over the serial interface using bit D1 of the Mode Register.
Analog Input Channel 4 or Digital Output 0. T his pin can be used as either an analog input or a digital
output bit as determined by the DEN bit of the Mode Register. When selected as a programmable-gain
analog input, it can be used as a pseudo-differential input when used with AIN6 or as the negative input of a
differential pair when used with AIN3. When selected as a digital output, this output can be programmed
over the serial interface using bit D0 of the Mode Register.
Reference Input. Positive terminal of the differential reference input to the AD7731. REF IN(+) can lie
anywhere between AV
DD
and AGND. T he nominal reference voltage (i.e., the differential voltage between
REF IN(+) and REF IN(–)) should be +2.5 V when the HIREF bit of the Mode Register is 0 and is +5 V
when the HIREF bit of the Mode Register is 1.
Reference Input. Negative terminal of the differential reference input to the AD7731. T he REF IN(–) can lie
anywhere between AV
DD
and AGND.
Analog Input Channel 5. Programmable-gain analog input which can be used is the positive input of a differ-
ential pair when used with AIN6.
Analog Input Channel 6. Reference point for AIN1 through AIN4 in pseudo-differential mode or as the
negative input of a differential input pair when used with AIN5.
Logic Input. T aking this pin low shuts down the analog and digital circuitry, reducing current consumption
to the 10
μ
A range. T he on-chip registers retain all their values when the part is in standby mode.
Chip Select. Active low L ogic Input used to select the AD7731. With this input hardwired low, the
AD7731 can operate in its three-wire interface mode with SCLK , DIN and DOUT used to interface to the
device.
CS
can be used to select the device in systems with more than one device on the serial bus or as a
frame synchronization signal in communicating with the AD7731.
4
POL
5
SYNC
6
RESET
7
8
9
10
NC
AGND
AV
DD
AIN1
11
AIN2
12
AIN3/D1
13
AIN4/D0
14
REF IN(+)
15
REF IN(–)
16
AIN5
17
AIN6
18
STANDBY
19
CS
相關PDF資料
PDF描述
EVAL-AD7751EB Energy Metering IC With On-Chip Fault Detection
EVAL-AD7755EB Energy Metering IC with Pulse Output
EVAL-AD7783EB Read-Only, Pin Configured 24-Bit ADC with Excitation Current Sources
EVAL-AD7843CB Touch Screen Digitizer
EVAL-AD7851CB 14-Bit 333 kSPS Serial A/D Converter
相關代理商/技術參數
參數描述
EVAL-AD7731EBZ 功能描述:BOARD EVALUATION FOR AD7731 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7732EB 制造商:Analog Devices 功能描述:2-CHANNEL, ??10 V INPUT RANGE, HIGH THROUGHPUT, 24-BIT ADC
EVAL-AD7732EBZ 功能描述:BOARD EVAL FOR AD7732 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7734EBZ 功能描述:BOARD EVALUATION FOR AD7734 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7738EB 制造商:Analog Devices 功能描述:Evaluation Board For AD7738 ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*