參數資料
型號： EVAL-AD7731EB
廠商： Analog Devices, Inc.
英文描述： Low Noise, High Throughput 24-Bit Sigma-Delta ADC
中文描述： 低噪聲，高吞吐量的24位Σ-Δ模數轉換器
文件頁數： 16/44頁
文件大小： 411K
代理商： EVAL-AD7731EB
AD7731
–16–
REV. 0
MD2
MD1
MD0
Operating Mode
0
0
0
Sync (Idle) Mode. In this mode, the modulator and filter are held in reset mode and the AD7731 is not
processing any new samples or data. Placing the part in this mode is equivalent to exerting the
SYNC
input pin. However, exerting the
SYNC
does not actually force these mode bits to 0, 0, 0. T he part re-
turns to this mode after a calibration or after a conversion in Single Conversion Mode. T his is the default
condition of these bits after Power-On/Reset.
Continuous Conversion Mode. In this mode, the AD7731 is continuously processing data and providing
conversion results to the Data Register at the programmed output update rate (as determined by the
Filter Register). For most applications, this would be the normal operating mode of the AD7731.
Single Conversion Mode. In this mode, the AD7731 performs a single conversion, updates the Data
Register, returns to the Sync Mode and resets the mode bits to 0, 0, 0. T he result of the single conversion
on the AD7731 in this mode will not be provided until the full settling-time of the filter has elapsed.
Power-Down (Standby) Mode. In this mode, the AD7731 goes into its power-down or standby state. Placing
the part in this mode is equivalent to exerting the
STANDBY
input pin. However, exerting
STANDBY
does
not actually force these mode bits to 0, 1, 1.
Zero-Scale Self-Calibration Mode. T his activates zero-scale self-calibration on the channel selected by the
CH2, CH1 and CH0 bits of the Mode Register. T his zero-scale self-calibration is performed at the se-
lected gain on internally shorted (zeroed) inputs. When this zero-scale self-calibration is complete, the
part updates the contents of the Offset Calibration Register and returns to Sync Mode with MD2, MD1
and MD0 returning to 0, 0, 0. T he
RDY
output and bit go high when calibration is initiated and return
low when this zero-scale self-calibration is complete to indicate that the part is back in Sync Mode and
ready for further operations.
Full-Scale Self-Calibration Mode. T his activates full-scale self-calibration on the channel selected by the
CH2, CH1 and CH0 bits of the Mode Register. T his full-scale self-calibration is performed at the se-
lected gain on an internally-generated full-scale signal. When this full-scale self-calibration is complete,
the part updates the contents of the Gain Calibration Register and returns to Sync Mode with MD2,
MD1 and MD0 returning to 0, 0, 0. T he
RDY
output and bit go high when calibration is initiated and
return low when this full-scale self-calibration is complete to indicate that the part is back in Sync Mode
and ready for further operations.
Zero-Scale System Calibration Mode. T his activates zero scale system calibration on the channel selected
by the CH2, CH1 and CH0 bits of the Mode Register. Calibration is performed at the selected gain on
the input voltage provided at the analog input during this calibration sequence. T his input voltage should
remain stable for the duration of the calibration. When this zero-scale system calibration is complete, the
part updates the contents of the Offset Calibration Register and returns to Sync Mode with MD2, MD1
and MD0 returning to 0, 0, 0. T he
RDY
output and bit go high when calibration is initiated and return
low when this zero-scale calibration is complete to indicate that the part is back in Sync Mode and ready
for further operations.
Full-Scale System Calibration Mode. T his activates full-scale system calibration on the selected input
channel. Calibration is performed at the selected gain on the input voltage provided at the analog input
during this calibration sequence. T his input voltage should remain stable for the duration of the calibra-
tion. When this full-scale system calibration is complete, the part updates the contents of the Gain Cali-
bration Register and returns to Sync Mode with MD2, MD1 and MD0 returning to 0, 0, 0. T he
RDY
output and bit go high when calibration is initiated and return low when this full-scale calibration is com-
plete to indicate that the part is back in Sync Mode and ready for further operations.
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
相關PDF資料
PDF描述
EVAL-AD7751EB Energy Metering IC With On-Chip Fault Detection
EVAL-AD7755EB Energy Metering IC with Pulse Output
EVAL-AD7783EB Read-Only, Pin Configured 24-Bit ADC with Excitation Current Sources
EVAL-AD7843CB Touch Screen Digitizer
EVAL-AD7851CB 14-Bit 333 kSPS Serial A/D Converter
相關代理商/技術參數
參數描述
EVAL-AD7731EBZ 功能描述:BOARD EVALUATION FOR AD7731 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7732EB 制造商:Analog Devices 功能描述:2-CHANNEL, ??10 V INPUT RANGE, HIGH THROUGHPUT, 24-BIT ADC
EVAL-AD7732EBZ 功能描述:BOARD EVAL FOR AD7732 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7734EBZ 功能描述:BOARD EVALUATION FOR AD7734 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7738EB 制造商:Analog Devices 功能描述:Evaluation Board For AD7738 ADC 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*