- 您現在的位置：買賣IC網 > PDF目錄362800 > EVAL-AD5383EB (Analog Devices, Inc.) 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC PDF資料下載
參數資料
| 型號： | EVAL-AD5383EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
| 中文描述： | 32通道，3伏/ 5 V，單電源，12位，電壓輸出DAC |
| 文件頁數： | 26/40頁 |
| 文件大?。?/td> | 1201K |
| 代理商： | EVAL-AD5383EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD5383
AD5383 INTERFACES
The AD5383 contains both parallel and serial interfaces.
Furthermore, the serial interface can be programmed to be
either SPI, DSP, MICROWIRE, or I
2
C compatible. The SER/PAR
pin selects parallel and serial interface modes. In serial mode,
the SPI/I2C pin is used to select DSP, SPI, MICROWIRE, or I
2
C
interface mode.
Rev. 0 | Page 26 of 40
The devices use an internal FIFO memory to allow high speed
successive writes in parallel interface mode. The user can con-
tinue writing new data to the device while write instructions are
being executed. The BUSY signal indicates the current status of
the device, going low while instructions in the FIFO are being
executed. In parallel mode, up to 128 successive instructions can
be written to the FIFO at maximum speed. When the FIFO is
full, any further writes to the device are ignored.
To minimize both the power consumption of the device and the
on-chip digital noise, the active interface only powers up fully
when the device is being written to, i.e., on the falling edge of
WR or the falling edge of SYNC.
DSP, SPI, MICROWIRE COMPATIBLE SERIAL
INTERFACES
The serial interface can be operated with a minimum of three
wires in standalone mode or four wires in daisy-chain mode.
Daisy chaining allows many devices to be cascaded together to
increase system channel count. The SER/PAR pin must be tied
high and the SPI/I2C pin (Pin 97) should be tied low to enable
the DSP/SPI/MICROWIRE compatible serial interface. In serial
interface mode, the user does not need to drive the parallel
input data pins. The serial interface’s control pins are
SYNC, DIN, SCLK
—Standard 3-Wire Interface Pins.
DCEN
—Selects Standalone Mode or Daisy-Chain Mode.
SDO
—Data Out Pin for Daisy-Chain Mode.
Figure 3 and Figure 5 show timing diagrams for a serial write to
the AD5383 in standalone and daisy-chain modes. The 24-bit
data-word format for the serial interface is shown in Table 19
A/B
. When toggle mode is enabled, this pin selects whether the
data write is to the A or B register. With toggle disabled, this bit
should be set to zero to select the A data register.
R/W
is the read or write control bit.
A4–A0
are used to address the input channels.
REG1 and REG0
select the register to which data is written, as
shown in Table 11.
DB11–DB0
contain the input data-word.
X
is a don’t care condition.
Standalone Mode
By connecting the DCEN (Daisy-Chain Enable) pin low, stand-
alone mode is enabled. The serial interface works with both a
continuous and a noncontinuous serial clock. The first falling
edge of SYNC starts the write cycle and resets a counter that
counts the number of serial clocks to ensure that the correct
number of bits are shifted into the serial shift register. Any
further edges on SYNC except for a falling edge are ignored
until 24 bits are clocked in. Once 24 bits have been shifted in,
the SCLK is ignored. In order for another serial transfer to take
place, the counter must be reset by the falling edge of SYNC.
Table 19. 40-Channel, 12-bit DAC Serial Input Register Configuration
MSB
A/B
R/W
0
A4
A3
A2
A1
A0
REG1
REG0
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
X
LSB
X
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5398EB | 120 mA, Current Sinking, 10-Bit, I2C DAC |
| EVAL-AD5415EB | Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Serial Interface |
| EVAL-AD5426EB | 8-/10-/12-Bit High Bandwidth Multiplying DACs with Serial Interface |
| EVAL-AD5432EB | CAP, .22UF, 10V, SMT, 0603 |
| EVAL-AD5443EB | CAP X7R 470PF 50V 10% 0603 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5390EB | 制造商:Analog Devices 功能描述: |
| EVAL-AD5390EBZ | 功能描述:BOARD EVALUATION FOR AD5390 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5391EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-AD5391EBZ | 功能描述:BOARD EVALUATION FOR AD5391 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5392EB | 制造商:Analog Devices 功能描述:EVAL BD FOR 8-/16CH, 3V/5 V, SERL INPUT, SGL-SUPPLY,12-/14BI - Bulk |
發布緊急采購，3分鐘左右您將得到回復。