- 您現在的位置：買賣IC網 > PDF目錄362800 > EVAL-AD5383EB (Analog Devices, Inc.) 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC PDF資料下載
參數資料
| 型號： | EVAL-AD5383EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 32-Channel, 3 V/5 V, Single-Supply, 12-Bit, Voltage Output DAC |
| 中文描述： | 32通道，3伏/ 5 V，單電源，12位，電壓輸出DAC |
| 文件頁數： | 15/40頁 |
| 文件大小： | 1201K |
| 代理商： | EVAL-AD5383EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD5383
Mnemonic
MON_OUT
Rev. 0 | Page 15 of 40
Function
When the monitor function is enabled, this output acts as the output of a 36-to-1 channel multiplexer that can be
programmed to multiplex one of Channels 0 to 31or any of the monitor input pins (MON_IN1 to MON_IN4) to the
MON_OUT pin. The MON_OUT pin’s output impedance is typically 500 , and is intended to drive a high input
impedance like that exhibited by SAR ADC inputs.
MON_IN Monitor Input Pins. The AD5383 contains four monitor input pins that allow the user to connect input
signals within the maximum ratings of the device to these pins for monitoring purposes. Any of the signals applied
to the MON_IN pins along with the 32 output channels can be switched to the MON_OUT pin via software. An
external ADC for example can be used to monitor these signals.
Interface Select Input. This pin allows the user to select whether the serial or parallel interface will be used. If it is tied
high, the serial interface mode is selected and Pin 97 (SPI/I2C) is used to determine if the interface mode is SPI or I
2
C.
Parallel interface mode is selected when SER/PAR is low.
In parallel interface mode, this pin acts as chip select input (level sensitive, active low). When low, the AD5383 is
selected.
Serial Interface Mode. This is the frame synchronization input signal for the serial clocks before the addressed
register is updated.
I
2
C Mode. This pin acts as a hardware address pin used in conjunction with AD1 to determine the software address
for the device on the I
2
C bus.
Multifunction Pin. In parallel interface mode, this pin acts as write enable. In serial interface mode, this pin acts as a
daisy-chain enable in SPI mode and as a hardware address pin in I
2
C mode.
Parallel Interface Write Input (edge sensitive). The rising edge of WR is used in conjunction with CS low and the
address bus inputs to write to the selected device registers.
Serial Interface. Daisy-chain select input (level sensitive, active high). When high, this signal is used in conjunction
with SER/PAR high to enable the SPI serial interface Daisy-Chain mode.
I
2
C Mode. This pin acts as a hardware address pin used in conjunction with AD0 to determine the software address
for this device on the I
2
C bus.
Parallel Data Bus. DB11 is the MSB and DB0 is the LSB of the input data-word on the AD5383.
Parallel Address Inputs. A5 to A0 are decoded to address one of the AD5383’s 40 input channels. Used in conjunction
with the REG1 and REG0 pins to determine the destination register for the input data.
In parallel interface mode REG1 and REG0 are used in decoding the destination registers for the input data. REG1 and
REG0 are decoded to address the input data register, offset register, or gain register for the selected channel and are
also used to decide the special function registers.
Serial Data Output in Serial Interface Mode. Three-stateable CMOS output. SDO can be used for daisy-chaining a
number of devices together. Data is clocked out on SDO on the rising edge of SCLK, and is valid on the falling edge
of SCLK.
When operating in parallel interface mode, this pin acts as the A or B data register select when writing data to the
AD5383’s data registers with toggle mode selected (see the Toggle Mode Function section). In toggle mode, the
LDAC is used to switch the output between the data contained in the A and B data registers. All DAC channels
contain two data registers. In normal mode, Data Register A is the default for data transfers.
Digital CMOS Output. BUSY goes low during internal calculations of the data (x2) loaded to the DAC data register.
During this time, the user can continue writing new data to the x1, c, and m registers in parallel mode (these are
stored in a FIFO), but no further updates to the DAC registers and DAC outputs can take place. If LDAC is taken low
while BUSY is low, this event is stored. BUSY also goes low during power-on reset, and when the BUSY pin is low.
During this time, the interface is disabled and any events on LDAC are ignored. A CLR operation also brings BUSY
low.
Load DAC Logic Input (Active Low). If LDAC is taken low while BUSY is inactive (high), the contents of the input
registers are transferred to the DAC registers and the DAC outputs are updated. If LDAC is taken low while BUSY is
active and internal calculations are taking place, the LDAC event is stored and the DAC registers are updated when
BUSY goes inactive. However any events on LDAC during power-on reset or on RESET are ignored.
Asynchronous Clear Input. The CLR input is falling edge sensitive. When CLR is activated, all channels are updated
with the data contained in the CLR code register. BUSY is low for a duration of 35 μs while all channels are being
updated with the CLR code.
Asynchronous Digital Reset Input (Falling Edge Sensitive). The function of this pin is equivalent to that of the power-
on reset generator. When this pin is taken low, the state machine initiates a reset sequence to digitally reset the x1,
m, c, and x2 registers to their default power-on values. This sequence typically takes 270 μs. The falling edge of RESET
initiates the RESET process and BUSY goes low for the duration, returning high when RESET is complete. While BUSY
is low, all interfaces are disabled and all LDAC pulses are ignored. When BUSY returns high, the part resumes normal
operation and the status of the RESET pin is ignored until the next falling edge is detected.
MON_INx
SER/PAR
CS/(SYNC/AD0)
WR/(DCEN/ AD1)
DB11–DB0
A4–A0
REG1, REG0
SDO/(A/B)
BUSY
LDAC
CLR
RESET
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5398EB | 120 mA, Current Sinking, 10-Bit, I2C DAC |
| EVAL-AD5415EB | Dual 12-Bit, High Bandwidth, Multiplying DAC with 4-Quadrant Resistors and Serial Interface |
| EVAL-AD5426EB | 8-/10-/12-Bit High Bandwidth Multiplying DACs with Serial Interface |
| EVAL-AD5432EB | CAP, .22UF, 10V, SMT, 0603 |
| EVAL-AD5443EB | CAP X7R 470PF 50V 10% 0603 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5390EB | 制造商:Analog Devices 功能描述: |
| EVAL-AD5390EBZ | 功能描述:BOARD EVALUATION FOR AD5390 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5391EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| EVAL-AD5391EBZ | 功能描述:BOARD EVALUATION FOR AD5391 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5392EB | 制造商:Analog Devices 功能描述:EVAL BD FOR 8-/16CH, 3V/5 V, SERL INPUT, SGL-SUPPLY,12-/14BI - Bulk |
發布緊急采購，3分鐘左右您將得到回復。