- 您現在的位置：買賣IC網 > PDF目錄362742 > EP7211-CP-A (CRYSTAL SEMICONDUCTOR CORP) HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER PDF資料下載
參數資料
| 型號： | EP7211-CP-A |
| 廠商： | CRYSTAL SEMICONDUCTOR CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PBGA256 |
| 封裝： | PLASTIC, BGA-256 |
| 文件頁數： | 61/166頁 |
| 文件大小： | 2623K |
| 代理商： | EP7211-CP-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁
EP7211
High-Performance Ultra-Low-Power System-on-Chip with LCD Controller
61
Functional Description
DS352PP3
JUL 2001
Data on the link is sent MSB first and coincides with an appropriate frame sync pulse, of one clock
in duration, located one clock prior to the first data bit sent (i.e., MSB). It is not possible to send data
LSB first.
When operating in master mode, the clock frequency is selected to be the same as the ADC
interface
’
s (master mode only SSI1)
—
that is, the frequencies are selected by the same bits 16 and
17 of the SYSCON1 register (i.e., the ADCKSEL bits). Thus, the maximum frequency in master
mode is 128 kbytes/s. The interface will support continuous transmission at this rate assuming that
the OS can respond to the interrupts within 1 ms to prevent over/underruns.
NOTE:
To allow synchronization to the incoming slave clock, the interface enable bits will not take effect until
one
SSICLK
cycle after they are written and the value read back from SYSCON2. The enable bits
reflect the real status of the enables internally. Hence, there will be a delay before the new value pro-
grammed to the enable bits can be read back.
The timing diagram for this interface can be found in the
AC Characteristics
section of this
document.
3.8.4.1
Read Back of Residual Data
All writes to the transmit FIFO must be in half-words (i.e., in units of two bytes at a time). On the
receive side, it is possible that an odd number of bytes will be received. Bytes are always loaded into
the receive FIFO in pairs, so in the case of a single residual byte remaining at the end of a
transmission, it will be necessary for the software to read the byte separately. This is done by reading
the status of two bits in the SYSFLG2 register to determine the validity of the residual data. These
two bits (RESVAL, RESFRM) are both set high when a residual is valid; RESVAL is cleared on
either a new transmission or on reading of the residual bit by software. RESFRM is cleared only on
a new transmission. By popping the residual byte into the RX FIFO and then reading the status of
these bits it is possible to determine if a residual bit has been correctly read.
Figure 3-8. Residual Byte Reading
illustrates this procedure. The sequence is as follows: read the
RESVAL bit, if this is a 0, no action needs to be taken. If this is a 1, then pop the residual byte into
the FIFO by writing to the SS2POP location. Then read back the two status bits RESVAL and
RESFRM. If these bits read back 01, then the residual byte popped into the FIFO is valid and can be
read back from the SS2DR register. If the bits are not 01, then there has been another transmission
received since the residual read procedure has been started. The data item that has been popped to
the top of the FIFO will be invalid and should be ignored. In this case, the correct byte will have been
stored in the most significant byte of the next half-word to be clocked into the FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| EP7211-CV-A | HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| EP7212 | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CB-A | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CV-A | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7309 | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EP7211-CV-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| EP7211-CV-D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EP7212 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CB-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CV-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
發布緊急采購，3分鐘左右您將得到回復。