- 您現在的位置：買賣IC網 > PDF目錄362742 > EP7211-CP-A (CRYSTAL SEMICONDUCTOR CORP) HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER PDF資料下載
參數資料
| 型號： | EP7211-CP-A |
| 廠商： | CRYSTAL SEMICONDUCTOR CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PBGA256 |
| 封裝： | PLASTIC, BGA-256 |
| 文件頁數： | 39/166頁 |
| 文件大?。?/td> | 2623K |
| 代理商： | EP7211-CP-A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁
EP7211
High-Performance Ultra-Low-Power System-on-Chip with LCD Controller
39
Functional Description
DS352PP3
JUL 2001
This would give a worst-case interrupt latency of about 19.3
μ
s for the ARM720T processor
operating at 13 MHz in this system. For those interrupt inputs which have de-glitching, this figure is
increased by the maximum time required to pass through the deglitcher, which is approximately 61
μ
s (1 cycle of the 16.384 kHz clock derived from the RTC oscillator). This would create an absolute
worst case latency of approximately 80
μ
s. If the ARM720T is run at 36 MHz or greater and/or 32-
bit wide external memory, the 19.3
μ
s value will be reduced.
All the serial data transfer peripherals included in the EP7211 (except for the master-only SSI1) have
local buffering to ensure a reasonable interrupt latency response requirement for the OS of 1 ms or
less. This assumes that the maximum data rates described in this specification are complied with. If
the OS cannot meet this requirement, there will be a risk of data over/underflow occurring.
3.3.1.2
Idle State
When leaving the Idle State as a result of an interrupt, the CPU clock is restarted after approximately
two clock cycles. However, there is still potentially up to 20
μ
s latency as described in the first
section above, unless the code is written to include at least two single cycle instructions immediately
after the write to the IDLE register (in which case the latency drops to a few microseconds). This is
important, as normally the Idle State will have been left because of a pending interrupt, which has to
be synchronized by the processor before it can be serviced.
3.3.1.3
Standby State
In the Standby State, the latency will depend on whether the system clock is shut down and if the
FASTWAKE bit in the SYSCON3 register is set. If the system is configured to run from the internal
PLL clock, then the PLL will always be shut down when in the Standby State. In this case, if the
FASTWAKE bit is cleared, then there will be a latency of between 0.125 s to 0.25 s. If the
FASTWAKE bit is set, then there will be a latency of between 250
μ
s to 500
μ
s. If the system is
running from the external clock (at 13 MHz), with the CLKENSL bit in SYSCON2 set to 0, then the
latency will also be between 0.125 s and 0.25 s to enable an external oscillator to stabilize. In the case
of a 13 MHz system where the clock is not disabled during the Standby State (CLKENSL = 1), then
the latency will be the same as described in the Idle State section above.
Whenever the EP7211 is in the Standby State, the external address and data buses are driven low.
The
RUN
signal is used internally to force these buses to be driven low. This is done to prevent
peripherals that are power-down from draining current. Also, the internal peripheral
’
s signals get set
to their Reset State.
相關PDF資料 |
PDF描述 |
|---|---|
| EP7211-CV-A | HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| EP7212 | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CB-A | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CV-A | HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7309 | HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EP7211-CV-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER |
| EP7211-CV-D | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| EP7212 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CB-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
| EP7212-CV-A | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI) |
發布緊急采購，3分鐘左右您將得到回復。