參數資料
型號： EP7211-CP-A
廠商： CRYSTAL SEMICONDUCTOR CORP
元件分類： 外設及接口
英文描述： HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
中文描述： MULTIFUNCTION PERIPHERAL, PBGA256
封裝： PLASTIC, BGA-256
文件頁數： 51/166頁
文件大?。?/td> 2623K
代理商： EP7211-CP-A
EP7211
High-Performance Ultra-Low-Power System-on-Chip with LCD Controller
51
Functional Description
DS352PP3
JUL 2001
3.8.1
Codec Sound Interface
The codec interface allows direct connection of a telephony type codec to the EP7211. It provides
all the necessary clocks and timing pulses and performs a parallel to serial conversion or vice versa
on the data stream to or from the external codec device. The interface is full duplex and contains two
separate data FIFOs (16 deep by 8-bits wide, one for the receive data, another for the transmit data).
Data is transferred to or from the codec at 64 kbps. The data is either written to or read from the
appropriate 16 byte FIFO. If enabled, a codec interrupt (CSINT) will be generated after every 8 bytes
are transferred (FIFO half full/empty). This means the interrupt rate will be every 1 ms, with a
latency of 1 ms.
Transmit and receive modes are enabled by asserting high both the CDENRX and CDENTX codec
enable bits in the SYSCON1 register.
NOTE:
Both the CDENRX and CDENTX enable bits should be asserted in tandem for data to be transmitted
or received. The reason for this is that the interrupt generation will occur 1 ms after one of the FIFOs
is enabled. For example: If the receive FIFO gets enabled first and the transmit FIFO at a later time,
the interrupt will occur 1 ms after the receive FIFO is enabled. After the first interrupt occurs, the
receive FIFO will be half full. However, it will not be possible to know how full the transmit FIFO will
be since it was enabled at a later time. Thus, it is possible to unintentionally overwrite data already in
the transmit FIFO. See the following diagram:
Figure 3-2. Codec Interrupt Timing
3.8.1.1
Codec Interrupt Timing
After the CDENRX and CDENTX enable bits get asserted, the corresponding FIFOs become
enabled. When deasserted low, the FIFO status flags (i.e., CRXFE and CTXFF located in the
SYSFLAG register) are cleared and the FIFOs appear empty. Additionally, if the CDENTX bit is
low, the PCMOUT output is disabled. Asserting either of the two enable bits causes the sync and
interrupt generation logic to become active; otherwise they are disabled to conserve power.
CDENRX
CDENTX
CSINT
1 ms
1 ms
1 ms
I
I
I
相關PDF資料
PDF描述
EP7211-CV-A HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7212 HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CB-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7309 HIGH PERFORMANCE LOW POWER SYSTEM ON CHIP ENHANCED DIGITAL AUDIO INTERFACE
相關代理商/技術參數
參數描述
EP7211-CV-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE ULTRA-LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER
EP7211-CV-D 制造商:Rochester Electronics LLC 功能描述:- Bulk
EP7212 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CB-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
EP7212-CV-A 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:HIGH-PERFORMANCE, LOW-POWER SYSTEM-ON-CHIP WITH LCD CONTROLLER AND DIGITAL AUDIO INTERFACE(DAI)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*