- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C924ADX (Cypress Semiconductor Corp.) 200 MBaud HOTLink Transceiver(200MBaud HOTLink收發器) PDF資料下載
參數資料
| 型號： | CY7C924ADX |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | 200 MBaud HOTLink Transceiver(200MBaud HOTLink收發器) |
| 中文描述： | 200 MBd的的HOTLink收發器（200MBaud的HOTLink收發器） |
| 文件頁數： | 5/58頁 |
| 文件大?。?/td> | 969K |
| 代理商： | CY7C924ADX |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
CY7C924ADX
Document #: 38-02008 Rev. *E
Page 5 of 58
20
TXSC/D*
TTL input, sampled
on
TXCLK
↑
or
REFCLK
↑,
Internal Pull Up
Transmit Special Character or Data Select Input
. When the Transmit FIFO
is enabled and the encoder is enabled (FIFOBYP* and ENCBYP* are HIGH),
this input is interpreted along with TXSVS and TXSOC (see
Table 2 on page
15
for details).
When the Transmit FIFO is bypassed and encoding is enabled (FIFOBYP* is
LOW and ENCBYP* is HIGH), this signal controls whether the TXDATA[7:0]
is sent as a data or control character.
When the encoder is bypassed (ENCBYP* is LOW) TXSC/D* is ignored.
Transmit Enable Input
. Data enable for the TXDATA[11:0] data bus write
operations. Active HIGH when configured for Cascade timing (EXTFIFO is
HIGH), active LOW when configured for UTOPIA timing (EXTFIFO is LOW).
When the Transmit FIFO is enabled (FIFOBYP* is HIGH) and TXEN* is
asserted, data loads into the FIFO on every rising edge of TXCLK. When
TXEN* is deasserted with TXHALT* and TXSTOP* deasserted, data
continues to read out of the Transmit FIFO and is sent serially until the FIFO
empties. At this time, C5.0 (K28.5) idle characters are transmitted.
When the Transmit FIFO is bypassed (FIFOBYP* is LOW) and TXEN* is
asserted, the parallel data on the TXDATA bus is clocked in and transmitted
on every appropriate REFCLK rising edge. When TXEN* is deasserted, the
parallel data bus is ignored and C5.0 sync characters are transmitted instead.
Transmit Stop on Start_Of_Cell Input
. While the Transmit FIFO and encoder
are enabled (FIFOBYP* and ENCBYP* are HIGH), this signal is used to
prevent queued data characters from being serially transmitted. While
TXSTOP* is deasserted, data flows through the Transmit FIFO without inter-
ruption. When TXSTOP* is asserted, data transfers continue until a TXSOC
bit is detected in the character stream, at which point data transmission
ceases. When transmission is stopped, C5.0 (K28.5) characters are sent
instead.
If data transmission is suspended due to a SOC character, pulsing TXSTOP*
deasserted then asserted will allow only the next cell (delimited by SOC bits)
to be transmitted.
When the Transmit FIFO is bypassed (FIFOBYP* = LOW) TXSTOP* has no
function.
When the Transmit FIFO is enabled (FIFOBYP* is HIGH) and the encoder is
bypassed (ENCBYP* is LOW), TXDATA[9]/TXHALT* is a data input and not
TXHALT*. In this mode, the TXSOC bit is not interpreted and the TXSTOP*
input assumes the same operation as TXHALT*. When TXSTOP* is asserted,
data reads from the Transmit FIFO are suspended and alternating disparity
10 bit equivalents of C5.0 are transmitted instead.
Transmit FIFO Clock
. The input clock for the parallel interface when the
Transmit FIFO is enabled (FIFOBYP* is HIGH). Samples all Transmit FIFO
related interface signals.
Transmit FIFO Full Status Flag
. Active HIGH when configured for Cascade
timing (EXTFIFO is HIGH), active LOW when configured for UTOPIA timing
(EXTFIFO is LOW). The TXFULL* output is enabled when AM* is asserted,
otherwise it is High-Z.
When the Transmit FIFO is enabled (FIFOBYP* is HIGH), TXFULL* indicates
a Transmit FIFO full condition. When TXFULL* is first asserted, the Transmit
FIFO accepts up to eight additional write cycles without data loss.
When the Transmit FIFO is bypassed (FIFOBYP* is LOW), with RANGESEL
HIGH or SPDSEL LOW, TXFULL* toggles at half the REFCLK rate to provide
a character rate indication.
18
TXEN*
TTL input, sampled
on
TXCLK
↑
or
REFCLK
↑,
Internal Pull Up
9
TXSTOP*
TTL input, sampled
on
TXCLK
↑
,
Internal Pull Up
68
TXCLK
TTL clock input,
Internal Pull Up
72
TXFULL*
3-state TTL output,
changes following
TXCLK
↑
or
REFCLK
↑
Pin Descriptions
(continued)
CY7C924ADX HOTLink Transceiver
Pin
Number
Name
I/O Characteristics
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C924DX | 200-MBaud HOTLink Transceiver(200H波特?zé)峤硬迨瞻l(fā)器) |
| CY7C954DX | ATM HOTLink Transceiver(ATM 熱接插收發器) |
| CY7C964A | Bus Interface Logic Circuit |
| CY7C964A-UM | Bus Interface Logic Circuit |
| CY7C964A-UMB | Bus Interface Logic Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C924ADX-AC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述: |
| CY7C924ADX-ADI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述: |
| CY7C924ADX-AI | 制造商:Cypress Semiconductor 功能描述:Framer 5V 100-Pin TQFP |
| CY7C924ADX-AXC | 功能描述:網絡控制器與處理器 IC HOTLink DX COM RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CY7C924ADX-AXCKJ | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。