- 您現在的位置：買賣IC網 > PDF目錄369480 > BQ2083 Silicon Bridge Rectifiers PDF資料下載
參數資料
| 型號： | BQ2083 |
| 英文描述： | Silicon Bridge Rectifiers |
| 中文描述： | 銀紫荊星章符合電量監測計芯片的使用與BQ29311 |
| 文件頁數： | 46/54頁 |
| 文件大?。?/td> | 461K |
| 代理商： | BQ2083 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
SLUS573 JULY 2003
www.ti.com
46
Change Control
Charging Voltage
The 16-bit value,
Charging Voltage
DF 0x390x3a programs the ChargingVoltage( ) value broadcast to a smart
charger. It ialso sets the base value for determining overvoltage conditions during charging and voltage
compliance during a constant-voltage charging methodology. It is stored in mV.
Over Voltage
The 16-bit value,
Over Voltage Margin
DF 0x5a0x5b, sets the limit over ChargingVoltage( ) in mV that is to be
considered as an overvoltage charge-suspension condition.
Charging Current
ChargingCurrent( ) values are either broadcast to a Level 2 smart battery charger or read from the bq2083V1P2
by a Level 3 smart battery charger. The bq2083V1P2 sets the value of ChargingCurrent( ), depending on the
charge requirements and charge conditions of the pack.
When fast charge is allowed, the bq2083V1P2 sets ChargingCurrent( ) to the rate programmed in
Fast-Charging
Current
DF 0x3d0x3e.
Fast-Charging Current
is stored in mA.
When fast charge terminates, the bq2083V1P2 sets ChargingCurrent( ) to zero and then to the
Maintenance
Charging Current
DF 0x3f, 0x40 when the termination condition ceases. The desired maintenance current is
stored in mA.
When Voltage( ) is less than EDV0, the bq2083V1P2 sets ChargingCurrent( ) to
Precharge Current
DF 0x41,
0x42. Typically this rate is larger than the maintenance rate to charge a deeply depleted pack up to the point where
it may be fast charged. The desired precharge rate is stored in mA.
If temperature is between 0
°
and the precharge threshold PC (
°
C), the bq2083V1P2 sets ChargingCurrent( ) to
PreCharge Current.
The threshold is programmed in the
Precharge Temp
DF 0x43.
Precharge Temp
PC (
°
C)
0.1
The bq2083V1P2 also sets ChargingCurrent( ) to the precharge rate if Voltage( ) is less than the value
programmed in
Precharge Voltage
DF 0x3b0x3c.
Precharge Voltage
is programmed in mV.
Charge Suspension
During charge, the bq2083V1P2 compares the current to the ChargingCurrent( ) plus the value in
OverCurrent
Margin
DF 0x5c0x5d. If the pack is charged at a current above or equal to the ChargingCurrent( ) plus the
programmed value, the bq2083V1P2 sets ChargingCurrent( ) to zero to stop charging.
The desired
Overcurrent Margin
is programmed in mA.
The desired temperature threshold for charge suspension, MAXTEMP (
°
C), is programmed in
Max Temperature
DF 0x53, 0x54 and is stored as shown:
Max Temperature
MAXTEMP
0.1
The bq2083V1P2 clears the maximum temperature condition when Temperature( ) drops by the amount
programmed in
Temperature Hysteresis
DF 0x55 from MAXTEMP or when the temperature is less than or equal
to 43.0
°
C.
Temperature Hysteresis
is stored in
°
C.
The bq2083V1P2 suspends fast charge when fast charge continues past full by the amount programmed in
Maximum Overcharge
DF 0x4e-0x4f.
Maximum Overcharge
is programmed in mAh.
FULLY_CHARGED Bit Clear Threshold
The bq2083V1P2 clears the FULLY_CHARGED bit in BatteryStatus( ) when RelativeStateOfCharge( ) reaches
the value,
Fully Charged Clear %
DF 0x47.
Fully Charged Clear %
is an 8-bit value and is stored in percent.
(10)
(11)
相關PDF資料 |
PDF描述 |
|---|---|
| BQ2201PN-N | Fast Recovery Bridge Rectifiers |
| BQ2201S-N | Fast Recovery Bridge Rectifiers |
| BQ2201SN(NARROW) | Fast Recovery Bridge Rectifiers |
| BQ2201SN-N | Fast Recovery Bridge Rectifiers |
| BQ2212PN | Fast Recovery Bridge Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ20832DBT | 制造商:Texas Instruments 功能描述: |
| BQ20832DBTR | 制造商:Texas Instruments 功能描述: |
| BQ2083DBT | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2083DBTG4 | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2083DBTR | 功能描述:電池管理 SBS-Cmplnt Gas Gauge for Use w/BQ29311 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。